TRX250r.org

Author Topic: Roll design - gasgas 250 hybrid  (Read 3496 times)

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #15 on: November 29, 2017, 06:38:11 AM »
...

Offline hickwheeler

Re: Roll design - gasgas 250 hybrid
« Reply #16 on: November 29, 2017, 02:23:15 PM »
Looks like kick starter is going to be an issue. To bad it wasn't one with electric start
88 330 worked over by Pete
88 ct350pv (BOF Build)
89 440 Packard built pilot  (Sold)

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #17 on: November 29, 2017, 03:41:33 PM »
Looks like kick starter is going to be an issue. To bad it wasn't one with electric start

you are correct. I have a few ideas, if I am unsuccessful, there is an electric start kit.  It is expensive though.

Offline hickwheeler

Re: Roll design - gasgas 250 hybrid
« Reply #18 on: November 29, 2017, 06:19:09 PM »
Still going to be cool however you do it
88 330 worked over by Pete
88 ct350pv (BOF Build)
89 440 Packard built pilot  (Sold)

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #19 on: February 26, 2018, 02:08:42 PM »
some parts back from powder coat:

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #20 on: February 26, 2018, 02:10:27 PM »
...

Offline hickwheeler

Re: Roll design - gasgas 250 hybrid
« Reply #21 on: February 26, 2018, 02:51:03 PM »
Parts pile is looking good John
88 330 worked over by Pete
88 ct350pv (BOF Build)
89 440 Packard built pilot  (Sold)

Online Tbone07

Re: Roll design - gasgas 250 hybrid
« Reply #22 on: February 26, 2018, 04:19:46 PM »
The hammer-tone paint on the gull-wing swinger looks killer. Well done sir.
LED Performance 350 Sphynx - XC Machine
Laeger's-Roll-GThunder-HLS-PEP-HiPer-GBC

RIP Laz

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #23 on: February 27, 2018, 04:48:44 AM »
thanks guys.  i found someone who does the silver-vein PC the way it should be done.  some more pics of misc., parts.

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #24 on: March 05, 2018, 06:14:47 AM »
here is the front motor mounts test fit.  the white one is the 3d printed prototype.  the other side with the offset did not work, so i used a yfz mount to use to establish offset.

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #25 on: March 12, 2018, 08:15:21 AM »
here a fender install tease.  still a while away from the official install.  Plus I got the boy doing the wrenching.haha

Online Tbone07

Re: Roll design - gasgas 250 hybrid
« Reply #26 on: March 13, 2018, 03:58:02 PM »
Very nice! Good to see the young buck getting involved.
LED Performance 350 Sphynx - XC Machine
Laeger's-Roll-GThunder-HLS-PEP-HiPer-GBC

RIP Laz

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #27 on: March 14, 2018, 04:25:03 AM »
Very nice! Good to see the young buck getting involved.

not a bad start.  he isn't even 3 years old yet

Offline jcs003

Re: Roll design - gasgas 250 hybrid
« Reply #28 on: March 14, 2018, 04:29:12 AM »
chain alignment was a success.  no mods needed.

Online DOUGLAS

Re: Roll design - gasgas 250 hybrid
« Reply #29 on: March 17, 2018, 04:57:15 AM »
is this a stock motor ? what shocks are those they look like yfz ?
LED 363 87 stock frame