TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - traxman

Pages: [1] 2 3 ... 7
1
Engine and Bottom End / poor ignition
« on: March 07, 2016, 10:50:19 AM »
Check your pulse coil and that it is around .010"  to .013" also check your spark plug gap and make sure it's around .018 to .020" see if that helps..

2
Lounge / Non-250r tech question for you guys...
« on: February 23, 2016, 12:46:11 AM »
Diesel would be my weapon of choice.. Throw some in and go for a small ride...

3
Projects / The Hulk Build
« on: February 13, 2016, 11:33:01 PM »
You need 50.06mm it shouldn't idle on gas..

4
Projects / The Hulk Build
« on: February 13, 2016, 06:18:26 AM »
Quote from: mandom250r;64527
Puma keeps running away on alky but when I purge it with gas it idles and stays running.
Its not as hard to start as I thought it would be.

Fatten your needle up a couple turns then start backing (leaning) it out a half turn at a time till you get closer to it's happy spot then you can go in 1/4 turn increments to fine tune it..

5
Duner / Florence, Oregon Presidents weekend
« on: January 06, 2016, 12:06:12 AM »
Wow some notice.. Loren if the guys aren't willing to budge I'll bring the truck and trailer up and bring you guys down to Windy bay for the day.. That is if I can get away... :nightmare:  I'll start working on the wife..

6
Drag Racing / Hassy Sand Drag Toy Drive
« on: January 04, 2016, 07:21:36 PM »
Quote from: Saber569r;62828
Sure is. The mid to top end is crazy. Pulls so hard. She beat my bro's jerry hall lt 500 dyno'd at 75hp and I think I was a little lean, highest jet I could find was 220 still a little a learn, she ran good but would fall on face until 1/4 throttle. Never got hot though.



How does this sphinx compare power wise to your last one?? Not reliability, we know where you stand on that...Lol I was curious if your first sphynx was as quick..

7
Introductions / New member thanks
« on: January 03, 2016, 11:36:16 PM »
Quote from: Wrench U;62769
First of I would like to thank all of you for spending the time to post information that is helpful to others. It is! I've been watching this place from the sidelines and decided that I could be a contributing member and there's some really great people here. A little info on me, middle aged male, been riding 16 yrs, ridden lots of different atv, extensive automotive knowledge all aspect and areas, I'm a thinker/tinker to, Family Man, respectful, former polini tech, I wrenched at all amature nationals (Lorettas,ponca city,mini O's,world minis,lake Whitney,oak hill,Branson etc.) Been out of it for a while now. I like riding in dirt, live near pismo, love high desert riding. Lots of bikes. Learned to ride on 250r and a banshee. There's a whole lot more, but that's all u get.lol!  Thanks again, glad to be here.


Welcome to the site!! I see the words polini and tech in your description!!!  My son has a polini x3, where is a good place to purchase jets and needles??

8
Projects / Skeans' build
« on: December 06, 2015, 08:28:14 AM »
Quote from: Skeans1;61672
https://youtu.be/2RhblWaQgiI

Your video is set to private.... Geeze.......

9
Glad you figured it out..

10
Also check for fuel flow.. If your tank vent isn't breathing well enough eventually your tank will create a vacuum and starve your carb of fuel.. Pull the fuel line and let it drain the entire tank into can to see if your getting a vapor lock or poor fuel flow..

11
Engine and Bottom End / Saber 569???
« on: November 25, 2015, 08:38:13 PM »

12
Engine and Bottom End / Saber 569???
« on: November 25, 2015, 07:55:54 PM »
The liger is flat out ripping the cr 500 cases apart.. After a liger completely destroyed a set of lt 500 cases, Pete built a 1/2" steel adapter plate to prevent making welds on the lt cases and to stiffen the whole set-up up.  It still destroyed cases and twisted the steel plate over a 1/4". It doesn't matter what rod you use, that doesn't change your displacement. I haven't heard anyone using the ktm rod on the saber, only the artic cat rod and cr 500 rod.. My saber has ran the same cr500 rod for the last 8 years and is finally receiving a new one as we speak. Pete prefers the cr 500 rod simply due to rotating mass since it's 1/2 the weight of the artic cat rod (not literally 1/2, but a lot lighter).. My motor is currently a 532cc 97x72mm and on top of running methanol I've also put a 50hp shot of nitrous to it without hurting the cr500 rod, so I would think it'd be up to the challenge for any dune set-up.. Oh and my cylinder was one of the very first sabers cylinders and was a 95mm bore. Pete bored it for me to 97mm. They are all the same castings..

13
For Sale - Parts / Lrd double silencer Quiet Big bore.
« on: October 14, 2015, 08:31:18 PM »
Quote from: havinnoj;59941
[MENTION=74]traxman[/MENTION] - maybe cut your losses with the Hershberger fiasco and buy this engine skid :rofl:


Wow!....Way to nut punch a guy while he's down.. lol Now I know who my friends are.. Good luck with your sale..

14
Lounge / Everyone's profession
« on: October 13, 2015, 10:37:27 PM »
Quote from: Skeans1;59900

Some pictures of some poles we did in the 90's when I was a kid.

Sent from my SAMSUNG-SM-G890A using Tapatalk

The pole you did last night...



Man, your gay when your drunk.. lol

I'm a stripper.... and I'm broke..  I almost got paid once to leave, but the bouncer was too quick.. lmao..

15
Projects / Mini-tooth
« on: September 07, 2015, 04:31:31 PM »
Quote from: Pumashine;58167
Got the pipe back from chrome and the cylinder polished up.



You should try some of those pumashine exhaust hangers, cause your current system looks sketchy...:smug:

Pages: [1] 2 3 ... 7