TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Rupp250

Pages: [1] 2 3
1
Lounge / New to me house
« on: July 22, 2016, 10:43:13 PM »
Bought a new to me house. Less then 1 mile away from where we were. 4/2 2 car garage with an RV spot on the side where I can park the Toyhauler.

Plan to put a single car garage door on the backside of the garage so it is easy to get bikes into the backyard. Build a small shop in the back and try to keep the garage clear for at least a car.

House was cosmetically horrible.




2
Engine and Bottom End / ESR Cases
« on: December 21, 2015, 12:54:15 PM »
Going to be buying some here soon. Anyone have the black one? How is the finish holding up. Does it stain with dirt/mud? Will probably buy the complete bearings and seals/gasket kit as well. Is it truly complete?

3
Lounge / Replacement Gearsets
« on: October 29, 2015, 07:12:35 PM »
As we all know, finding replacement gears are getting harder and harder. There is a limited amount of Yukons NIW out there. LED has a replacement 2nd gear I believe. I've spoke with Nate Mccoy about his billet drag setups, he has none left if you are wondering. I've also spoke with him about doing replacement gears.

Is there any legitimate want/need out there for them. The ones he had made before were Billet Overrides(with a slightly different ratio) which included the drum.
Does anyone want an Override?
Does anyone want a replacement gearset?
No prices have been set and no date has been set. If you have any interest in either you can contact him @ 1-530-476-2222

4
Duner / Pismo dec 4-6
« on: October 13, 2015, 07:11:24 PM »
I know several on here ride there, but never can seem to meet up with anyone. I'll be there with the Fam, but if anyone wants to get in a ride hit me up.

Russell

5
Pics and Vids / Oakland monster trucks
« on: February 21, 2015, 10:26:23 PM »
Were here now. Get some.

6
Suspension and Chassis / 400EX spindle onto a 86?
« on: February 17, 2015, 10:22:12 AM »
What does it take to do it correctly? I have 2 sets of 400EX spindles sitting here that I could use. Plus I have 2 86's. Perfect match, right?

7
Engine and Bottom End / O-ring sizes
« on: January 21, 2015, 04:22:23 PM »
I'm going to order some o-rings from McMaster. I know just measure them and order. Well I am at work and doing 16 hr days and want to get them ordered.

Anyone know the O-ring sizes for the Sphinx and Puma cylinder heads, exhaust flanges as well?

Heck maybe list the sizes for any o-rings. ESR silencer etc...  Maybe it will help someone in the future.

8
Lounge / Did 3.5 hours of riding today.
« on: January 11, 2015, 09:28:45 PM »
And none of it done by me. My 4.5yo son Deegan getting it on the Lt80.

9
Lounge / Big Thanks to Schmidty Racing
« on: December 29, 2014, 12:22:09 PM »
Like the title says. I sent Evan a set of front shocks and a rear. I was on a time crunch for a camping trip that I am leaving for on Wednesday. He revalved/resprung them for me, replaced the rear shock shaft, and just in general cleaned up the shock bodies. I know he had other customers to get done as well. Plus he is going camping for the New Year as well. yet he was able to get my junk done.

Thanks Evan, I actually have another set I will be sending to you sometime this year off my trail bike.

10
Wanted / WTB 86-87 Swimgarm
« on: October 29, 2014, 12:17:03 PM »
Looking for an stock length aftermarket swing arm. Would prefer a round style over square but open to anything if price is right

11
Duner / Glamis New Year 2015
« on: October 16, 2014, 12:39:00 PM »
Well there will be a couple of us in Glamis for this New Year. Would be nice to plan a meet up for a ride or just to toss the B.S. around. We will most likely be in the washes. I think I am going to get there Tuesday the 30th, and leaving either Friday or Saturday. I will be roughing it in a tent, 565miles one way is a long ways to pull the trailer. Figure I can just toss the bike in the bed of the truck and do 80mph the whole way instead of doing 60mph with a trailer.

So who is going? When you going? Where you staying?

12
Wanted / WTB Bottom End
« on: October 07, 2014, 03:52:11 PM »
Looking for a bottom end for my next drag build. Looking for one setup with Lockout, cut trans or Nates gears, balanced crank for puma or bigger.

Let me know what you got or know of out there. Or if you have a complete motor.

13
Lounge / Been a little too busy
« on: August 21, 2014, 01:27:20 PM »
Well I started on my bike projects not too long ago. This is what I have been busy with. Look at that good loooking shirt.





And here is big brother Deegan holding Brayden.


14
Pics and Vids / Got away mid week
« on: August 08, 2014, 09:37:45 PM »
Went for a little ride the other day mid week. Had the place pretty much all to my self.







15
Projects / My Re-builds That are on Going
« on: August 08, 2014, 09:13:35 PM »
Well I figured I would chronicle the rebuild of a couple of my R's. I've slowly been collecting parts for a Drag/Dune bike. Had a lot of fun running it that way. but have recently picked up a dedicated drag chassis. Well it is still sitting 2hrs away for 3 months already paid for. So now I will have a dedicated Dune bike. I also picked up a stock 86 250r from a forum member back in April. This will be my trail bike.

So this bike will be going back to a Duner.

The plan so far is to run
363 Sphinx ported by Nate McCoy
ESR5CM piipe
+2 Arms
2+2 Durablue Axle I got from PortedR(AJ)
+1 Stem(Still need)
Aftermarket Stock Length SwingArm (Still need)
Works Shocks by Evan @ Schmidty Racing

I update the other stuff as I redo them.

This is the bike that will be staying fairly stock.

It will have
stock Cylinder setup by Nate McCoy
Works Shock from Scmidty

The drag Bike I will post pics and info as I get to it.
Wife is having our second son any day so racing and trips this year is done. My next ride will be Glamis for Newy Years and the drag bike should be ready for Bakersfield next year. Which is usually late March.

Pages: [1] 2 3