TRX250r.org

Author Topic: Anyone make fender brackets for Maiers  (Read 6059 times)

Offline Hawaiiysr

Anyone make fender brackets for Maiers
« Reply #15 on: February 20, 2014, 12:21:32 AM »
I like the way quadzilla rear fender supports are.

Offline Wes350x

Anyone make fender brackets for Maiers
« Reply #16 on: February 20, 2014, 07:35:56 PM »
Here's thr rod I bent and painted.


1988 250R

Offline bnau267

Anyone make fender brackets for Maiers
« Reply #17 on: February 21, 2014, 09:04:53 AM »
OK - we are in business.
Lowers = Wes350x
Uppers = rk88r
Design, Development, and Testing complete....now we need a Manufacturer/Distributor to set price and start filling orders.

Offline Wes350x

Anyone make fender brackets for Maiers
« Reply #18 on: February 21, 2014, 09:44:25 AM »
Quote from: bnau267;26340
OK - we are in business.
Lowers = Wes350x
Uppers = rk88r
Design, Development, and Testing complete....now we need a Manufacturer/Distributor to set price and start filling orders.


The ones I have on my fronts I believe anyone can make with a vise and hammer.  Cut to length, put in vise and bent the curve by hitting with a hammer using a bolt inside to make the curve. Prob would be super easy to heat it up good first. Then sanded and sprayed black. The rod was super cheap $.
1988 250R

Offline Pumashine

Anyone make fender brackets for Maiers
« Reply #19 on: February 21, 2014, 11:31:23 AM »
Quote from: Wes350x;26297
Here's thr rod I bent and painted.

Did you use the torch for that?  The rod looks to be about 3/16 in diameter?
Puma 408, Puma 431,  Pilot 412, Puma 431, Mini-tooth 486 Trx450r
89mm  Mini tooth Shearer in frame pipe chromed! Mounted with Cascade QUIET[/

Offline Wes350x

Anyone make fender brackets for Maiers
« Reply #20 on: February 21, 2014, 01:43:17 PM »
Quote from: Pumashine;26357
Did you use the torch for that?  The rod looks to be about 3/16 in diameter?


I believe I did use some heat from a propane torch to make it a little easier. I also think you are right, 3/16" stick.
1988 250R

Offline Tbone07

Anyone make fender brackets for Maiers
« Reply #21 on: February 21, 2014, 07:28:12 PM »
I would be very interested in this if I can't find Fullbores.

I think this is something that would sell very well.
LED Performance 350 Sphynx - XC Machine
Laeger's-Roll-GThunder-HLS-PEP-HiPer-GBC

RIP Laz

Offline mx250r91

Anyone make fender brackets for Maiers
« Reply #22 on: February 22, 2014, 10:32:19 AM »
I just bent some spring steel rod to attach the front fenders to the frame. My frame (aftermarket) doesn't even have provisions for the stock brackets so I attached them with stainless hose clamps. Ghetto but works flawlessly!




Offline nico

Anyone make fender brackets for Maiers
« Reply #23 on: February 24, 2014, 03:49:23 PM »
I made some years ago, using some 1/8" by 1" aluminum strap from Tractor Supply... Worked perfectly to drill bolt holes in each end, then bend to fit.  When I was done, I just sanded and polished them.  I have since replaced them with chrome stockers, just because I got some as part of a package deal parts swap.

Offline TRXforever

Anyone make fender brackets for Maiers
« Reply #24 on: May 11, 2014, 09:29:03 PM »
Quote from: Wes350x;26297
Here's thr rod I bent and painted.



Might you have, or can you get, another set of these??

Offline Wes350x

Anyone make fender brackets for Maiers
« Reply #25 on: May 11, 2014, 09:50:54 PM »
Quote from: TRXforever;33702
Might you have, or can you get, another set of these??

I don't, but they were pretty easy to make.
1988 250R