Messages

1

Pics and Vids / one heck of a collection

« on: August 05, 2016, 03:07:52 PM »

Just when u think your a hoarder something like this pops up and let's you know you could always be WAY WORSE! Glad to see that's there's every brand in there. Hey at least it's cheaper then cars. I hope he opens it up for tours that would be awesome.

2

Drag Racing / 250r Shootout pismo dunes

« on: August 05, 2016, 02:54:08 PM »

Saturday early should be great time Rupp.

3

Drag Racing / 250r Shootout pismo dunes

« on: August 04, 2016, 07:42:42 PM »

Wish I could make, but I'm busy. So just a heads up if your coming south on 101 make sure u give yourself extra travel time traffics been bad! From Gilroy to Greenfield, lots of construction,uneven roads, closed off ramps. It's bad worse then most summers. The air quality is bad to cause of the fire, lots of emergency vehicles everywhere. It's also harvest time. So be safe in your travels. P.S. I believe the mid state fair is also going on Paso Robles and its 100 degrees plus down there.

4

Body and Controls / Rear light compatability question

« on: June 09, 2016, 09:59:12 PM »

Well done! Clean install with the Banjo switch.

5

Projects / Project "Phoenix Rise"

« on: June 01, 2016, 07:52:17 PM »

Sorry miss read. Your just replacing ESR cylinder a new one.

6

Projects / Project "Phoenix Rise"

« on: June 01, 2016, 07:46:21 PM »

Glad to see your excited about new build. Cases look sweet. Keep us informed on build. I'm curious how ESR cylinder runs compared to Sphynx.

7

Lounge / New Family Member

« on: May 20, 2016, 10:39:05 PM »

Congratulations! New grandpa! Look at all that hair!

8

Projects / My LSR duner build

« on: May 17, 2016, 01:22:00 AM »

Looks great! Needs a blue nose(lol!), hood or bumper. U nailed it on the seat cover. Haven't seen a white themed bike I like as much as your. Awesome job!

9

Body and Controls / Rear light compatability question

« on: May 08, 2016, 06:52:25 PM »

The light and mounting for taillight is the easy part. Mounting the brake switch and making it functional, more of a obstacle. U can do it!

10

Body and Controls / What Grab Bars Fit TRX250R?

« on: April 16, 2016, 10:43:28 PM »

Bolt patterns easy to drill. The width is  more critical. Trx450r 04-05/ 06-09(u need to cut exhaust mount off) is the right width. Ltz400 is also the right width. I haven't confirmed 400ex but I think the 450r (04-05) use the same part numbers. This was a thread a while back. I took the actual width measurements.

11

Projects / Jakes 363 Build

« on: April 07, 2016, 11:44:42 PM »

Looks good, sounds good! I'm digging the color scheme.

12

Projects / My LSR duner build

« on: April 07, 2016, 11:37:54 PM »

Nice choice! Looks classy and sharp!

13

Projects / My Re-builds That are on Going

« on: April 01, 2016, 07:41:16 PM »

Life is full of hard decisions!

14

Suspension and Chassis / Thoughts and or where to buy ceramic bearings

« on: March 31, 2016, 05:44:47 PM »

If u look into it u will find that most ceramic bearings are hybrid style, steel cage, ceramic balls. With that being said jerry hit it right on the head, lots more performance benefits in minimizing rolling resistance/drag. Titanium is cheap relatively speaking when u start talking full ceramic bearings. U will also find that u cannot get every engine bearing in ceramic, so that defeats the purpose. Ceramic also still use a steel cage riveted together and do not like any contaminants cause or tight tolerances. With that being said I would use them on spindle mounted front wheels with titanium nut and cotter pin, only because it's easy to check and that's going to be popular/inexpensive size to run. My to cents, I'd rather REM the internals, way more gains per cost.

15

Engine and Bottom End / Hybrid Engineering 363

« on: March 26, 2016, 10:24:22 PM »

Any ride report?