TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jcs003

Pages: [1] 2 3 ... 5
1
Carburetor, Intake, and Exhaust / Titanium Exhaust
« on: November 24, 2023, 01:13:21 PM »
RP Race titanium exhaust.

2
Wanted / TRX250r Rad Valve
« on: June 08, 2019, 09:21:42 AM »
I am looking for a 250r rad valve.  not a cr250 type.

Let me know what you have.

Thank you.

John

3
Administration/Moderator Questions / PM Box Structure
« on: January 23, 2019, 11:53:01 AM »
can the PM structure be changed?  It is set up in an odd way that resembles a standard thread.

Thank you,

John

4
For Sale - Parts / Engine for sale.
« on: January 18, 2019, 06:51:27 AM »
I am selling an engine.  asking $1,000 shipped

-86 cases
-trail ported
-2001 cr ignition
-+4 crank (porting to match)
-Neil clutch mod
-polished side covers and cylinder.

Needs:

-bored/honed and piston.
-I would also replace the base studs.  showing signs of corrosion.

Will come with 3 A/S and all replacement gaskets.

Let me know if you have any questions.

5
Wanted / Silencer
« on: September 12, 2018, 02:09:04 PM »
I am looking for a silencer cheap.  Let me know what you have.

Thank you,

John

6
Wanted / 310 stroker cylinder
« on: August 15, 2018, 01:59:48 PM »
I am looking for a big bore stroker cylinder.  +4 to be accurate.

let me know what you have.

thank you,

john

7
Lounge / Street Legal ATV
« on: August 07, 2018, 01:14:53 PM »
This seems rather interesting:  https://www.dirtlegal.com/

John

8
Lounge / ESR - Sale
« on: August 03, 2018, 09:23:38 AM »
Cylinder kits are on sale over at ESR.  Big discounts.

John

9
Lounge / ATV Storage
« on: June 26, 2018, 07:55:36 AM »
I am looking for an ATV shelf of sorts.  something like below.  I cannot seem to find a manufacture and i have done cost analysis to make my own from metal.  considering aluminum tube, 80/20 and steel.  seems there is no inexpensive solution.  i assume one of these in the image would be more cost effective.

does anyone know a manufacturer of these or a suggestion for a more cost effective solution?

Thank you for any help.

John

10
Lounge / DIY epoxy floor coating
« on: May 23, 2018, 08:15:30 AM »
I am in the mdist of a DIY garage floor epoxy coating.

so far I have done the following:

- pressure washed
- cleaned with concrete cleaner and a brush.
- chemical etched
- cleaned and etched again

left to do:

- dry brush
- vacuum
- apply epoxy
- apply clear coat epoxy.

then I will move over to the other side of the garage.  this is the kit i used:  https://epoxymaster.com/

pics in its current state:



11
Wanted / Head Nuts
« on: May 10, 2018, 05:17:58 AM »
I am looking to buy a set of head nuts.  anyone have a nice, spare set?

The only place on ebay that has them is big dog turds.

John

12
Lounge / Cool Builds
« on: May 03, 2018, 01:44:57 PM »

15
Carburetor, Intake, and Exhaust / 36mm PWK Jetting
« on: March 19, 2018, 02:12:12 PM »
does anyone have ballpark/baseline jetting for a 36mm carb?  specifically, a 36mm pwk.

thank you,

John

Pages: [1] 2 3 ... 5