TRX250R.ORG
Site Sponsors => Pumashine 250R Products => Topic started by: Outlaw525 on September 07, 2013, 07:42:40 PM
-
Pumashine thanks for the Gusset kit looks great and have a question. I am wanting to put 450r foot pegs on my 1987 250r. I could make the brackets my self but I would have to cut them with a torch so that would weaken the steel. Could you make me a set I know you can't get the 250r pegs any were but you can get 450r pegs every where. I could post some pics with what I am looking to do if you are interested thanks
-
Yes, lets do it. Post a pic and I will cut you some beefy mounts. Have been wanting to do this for awhile. I have both quads so they will bolt up like OEM
-
I would love to see this. I really want foot pegs with heel guards for my 86. Been looking at 450s but haven't bit the bullet yet. I am not to good at fab work lol.
-
Ok here is some pics looks like it will work great. From what I mocked up pegs will set in the same place of the factory peg on the front side. You will have a choice on what height you want. I am a tall guy so I want mine to set a little lower. 450r foot peg mount are staggered so you can lower them by 1/2 in or stock height.
-
Pic of 450r pegs
-
Tony if you need some Pegs to use I would send these out to you. They are new take offs I got off eBay for $16 shiped. Thanks for the help I know I am not the only one looking for a foot peg option for the 86 and 87.
-
So we are looking at making a plate to bolt up to the existing holes. Using one hole from the 450 foot peg to bolt the peg in the frame. Another hole in the front to bolt up the front bolt hole of the 450 peg. So 3 holes total. The rear hole bolts the bracket to the frame. The middle hole bolts the rear hole of the 450 peg to the bracket and frame, A front hole to bolt the front of the 450 peg to. Is this what you are thinking?
-
Yes that is what I am looking for. see what you can do and let me know. Thanks
-
[ATTACH=CONFIG]1776[/ATTACH] Douglas has made these for his R
im not sure if he's done any more then this but I believe he is close to having them right were he wants them
I think he just needed to trim then down and clean them up a little
-
Yeah, you would be able to lower the whole peg that way since you are not using the stock mounting location. Outlaw525 is this what you were talking about when lowering them 1/2" for tall people?
-
The bracket in the pic is what I am looking for. You get the 1/2 in lower by the 450r pegs having a off set bolt patern. One bolt on the pegs are 1/2 in lower than the other bolt. If you switch them from one side or the other you get a 1/2 in drop or factory location. Bracket will have to be drilled different for each one. From the pic it looks like the bling star pegs are higher than the factory 450r pegs.
-
The bracket in the pic is what I am looking for. You get the 1/2 in lower by the 450r pegs having a off set bolt patern.
(http://trx250r.org/attachment.php?attachmentid=1776&d=1378682473&thumb=1)This pic? There are 2 sets of holes in this bracket. Your original pic showed one of the holes on the 450 pegs lining up with the frame. So 4 holes with one set 1/2" lower for the pegs to bolt to?
-
Want them just like you said. Rear upper bolt just throught the bracket and in frame. Next bolt throught peg then bracket and then frame. Last bolt in peg then bracket with a nut on back. Would end up with 3 hold in bracket. On the 3rd hole you can drill it ether 1/2 in hi or low and then the gets could be dropped 1/2 in from factory by switching the pegs from left to right side or right to left side. Look at the pick of the pegs I have thanks. Pegs are off of a 04/05 450r
-
Ok then, I will start making up some brackets. What thickness do you think they need to be? The ones Douglas made up are 1/4". The stock pegs use a 3/8" plate
-
I would use the 3/8 or 1/2. But if 3/8 has held up for 20 some years it will work for another 20 or as long as I can find parts for the old girl
-
But if 3/8 has held up for 20 some years it will work for another 20
Update on this project. I went on ebay and bought Honda TRX 450R Foot Pegs & Heal Guards---04-05 for $60 shipped. So the plan is to make a foot peg adapter for the 04/05. Another bracket that goes on the frame and secures the heel bucket. Once this is complete it will only take a small modification or none at all to use for the 06-13.
-
OK..........These are not as hefty as the ones Douglas made but I think they may look a tad better. I measured the height and were at 1/4" below OEM. As for front to back it matches the 450r. I will cut a pair of 3/8" thick tomorrow so you guys can see the end product. I ran out of battery on my camera. Sorry
(http://i44.tinypic.com/24qv59z.jpg)
-
Looks great Tony! I'm in for a set.. getting tired of the narrow RIS pegs so this makes moving to Roll pegs very attractive.
-
Looking good
-
Looking good
Got my camera charged. I am thinking we need to tap the front hole for a 10 MM bolt and order some OEM ones for the kits. 3/8" steel will give plenty of holding power for the 10mm bolt.
(http://i40.tinypic.com/2hxwr2d.jpg)
(http://i44.tinypic.com/dz7aqh.jpg)
(http://i41.tinypic.com/303aadl.jpg)
I checked about lowering pegs by 1/2" by swapping sides....actually raises them 1/2".. so that won't be happening unless both holes are moved down 1/2". Would have thread both those holes.
-
This is going to be great. Will love having wide pegs that don't move around and feal like they will fall off when I get on. And give every one a option for aftermarket pegs. I thank I bling star makes a set of pegs for a 450 that are -1 in. Will have to look into them if I need them to be lowered.for now stock 450r pegs will work. Or at least tell winter when she gets torn apart for restoration.
-
I ordered bolts so you guys can install these in a few minutes. Plan on just painting them black. These are the final parts made from 3/8" steel.
(http://i44.tinypic.com/2gx2wsg.jpg)
-
When you going to have everything ready to ship and how much for my set. That way I can get you payed. Thanks
-
I ordered the bolts. I am still tapping the 10mm fine thread holes. Going to send all the parts off to get black anodized. So we are still a couple weeks out.
-
How's it coming on the mounts.
-
I finally got the parts, bolts and washers bead blasted and clean out to black zinc. Should be 4 - 5 days. (http://www.sympato.ch/smileys/Boobies2.gif)
-
How'd they turn out.
-
How'd they turn out.
The black zinc turned out great.
(http://i39.tinypic.com/hwe8fl.jpg)
Cost for the set of 3/8" thick adapters and bolts for foot peg adapters is $24. The stock flange bolt will need to be reused for the rear hole mount. $6 to ship puts the total cost at $30 for the set shipped.
(http://i39.tinypic.com/vik4ki.jpg)
(http://i42.tinypic.com/snoxuf.jpg)
(http://i43.tinypic.com/znn6af.jpg)
(http://i40.tinypic.com/jzdtah.jpg)
-
How many set did you make to sell? Or are they accounted for?
-
How many set did you make to sell? Or are they accounted for?
I took a gamble and built 30 sets. There is a minimum of $80 on black zinc plate. The bolts come black iron but would rust once they got wet. The bolts were bead blasted clean and baked after plating to put the strength back in them. I will be putting them on the website this week.
-
They look great. That engine looks very cool with the stardust.