TRX250R.ORG

Site Sponsors => Pumashine 250R Products => Topic started by: atvmxr on May 31, 2014, 08:30:40 PM

Title: Fabrication request
Post by: atvmxr on May 31, 2014, 08:30:40 PM: [MENTION=9]Pumashine[/MENTION]

Think you can make something like this? It the oem 86-87 steering stem handlebar/headlight mount, cut up to fit over an aftermarket stem and provide way to mount headlight.

Credit to gooch on the other site

:positive:
Title: Fabrication request
Post by: Pumashine on May 31, 2014, 08:36:26 PM: Quote from: atvmxr;35460
[MENTION=9]Pumashine[/MENTION]

Think you can make something like this? It the oem 86-87 steering stem handlebar/headlight mount, cut up to fit over an aftermarket stem and provide way to mount headlight.
Anything can be made but this one I cannot make cost effective. If someone created this part then it is best to go to that guy to get it made.
Title: Fabrication request
Post by: bnau267 on May 31, 2014, 10:32:27 PM: Quote from: Pumashine;35462
Anything can be made but this one I cannot make cost effective. If someone created this part then it is best to go to that guy to get it made.

But just maybe you'll think up a new more cost friendly design!
Title: Fabrication request
Post by: Rupp250 on June 01, 2014, 09:41:11 AM: Most people don't want to pay for R&D for there one off project. Or they don't realize hourly shop rates are not the same across this vast country.
My local fab shops around here have a $125 per hour rate and a $150 minimum. Unless someone see that they can make several of one item, and spread the costs out, a one off gets pricey.
Title: @Kasey
Post by: Pumashine on December 28, 2014, 04:27:45 PM: Heres the new 3/4" thick triple tree [MENTION=145]KASEY[/MENTION] wanted made up for his next build.

(http://i61.tinypic.com/25i0vhi.jpg)
Title: Fabrication request
Post by: KASEY on December 29, 2014, 08:58:39 AM: YES YES YES!!!!!! pm me the details,,, and I want a plain el cheapo motor stand ,, I am going to paint it to match my new paper weight !
Title: Fabrication request
Post by: Pumashine on December 29, 2014, 10:25:56 AM: Quote from: KASEY;48156
YES YES YES!!!!!! pm me the details,,, and I want a plain el cheapo motor stand ,, I am going to paint it to match my new paper weight !

As per your request I am cutting TRX250r motor stands without the Honda logo for cheap$$$. Aluminum and steel.
Title: Fabrication request
Post by: KASEY on December 29, 2014, 01:38:21 PM: Let me know how much and i will get it done.... WOOOOOO HOOOO ready for the clamps ...
Title: Fabrication request
Post by: JesseA420 on December 29, 2014, 02:07:59 PM: me likey that pinch design ;)
Title: Fabrication request
Post by: Pumashine on April 25, 2015, 08:54:33 PM: Kasey has alot of ideas for make trick parts for building ??? The small hubs have a 3 on 100mm BHC. He sent me the first pic but it is hard to duplicate because it is not to scale. I sent croat1 the pic+info and he sent me a file to cut the small hub. I modified his original file to what is now cut. Thanks Joe.
(http://i1141.photobucket.com/albums/n592/KASEYII/0412151925%201.jpg)
(http://i59.tinypic.com/jfx5s5.jpg)
Title: Fabrication request
Post by: JesseA420 on April 25, 2015, 09:15:41 PM: looks sweet, i would have drawn the width of the center circle the same width as the width of the legs, the legs look a bit wider than the center circle but im sure they will work fine.
Title: Fabrication request
Post by: Pumashine on April 25, 2015, 09:43:27 PM: Quote from: JesseA420;53703
looks sweet, i would have drawn the width of the center circle the same width as the width of the legs, the legs look a bit wider than the center circle but im sure they will work fine.

Anything can be drawn. If it is not to scale then the physical limitations cannot be addressed.
Title: Fabrication request
Post by: KASEY on April 25, 2015, 11:12:54 PM: those are for ME!!!!!! OHHH MAN,, as of now i am with wood!! here is what i do... (http://forums.trx250r.org/vbulletin_imports/145_2352_2017-04-18_6477.gif)
Title: Fabrication request
Post by: KASEY on April 25, 2015, 11:24:19 PM: i am real excited to challenge tony, so far he has done a fantastic job on all the goodies ... true craftsman ,,,, i made some hubs out of stock hubs and then went a step higher ,, results as seen ,, wagon hubs ,, that's right wagon,,,,

(http://forums.trx250r.org/vbulletin_imports/145_5199_2017-04-18_5011.jpg) (http://forums.trx250r.org/vbulletin_imports/145_5200_2017-04-18_1350.jpg)(http://forums.trx250r.org/vbulletin_imports/145_5201_2017-04-18_5706.jpg)(http://forums.trx250r.org/vbulletin_imports/145_4765_2017-04-18_2239.jpg)
Title: Fabrication request
Post by: KASEY on April 25, 2015, 11:31:42 PM: Quote from: JesseA420;53703
looks sweet, i would have drawn the width of the center circle the same width as the width of the legs, the legs look a bit wider than the center circle but im sure they will work fine.

we talked about that,, but i it wouldn't have looked as EXTREME and that's what i wanted,, they look perfect... bringing the imaginary second circle in helped make that happen ,, the fingers would not be as KOOOOL if you did it that way,,,,
Title: Fabrication request
Post by: JesseA420 on April 27, 2015, 06:47:18 AM: ya they do look sweet, going to make for a super cool setup :D
Title: Fabrication request
Post by: KASEY on May 02, 2015, 01:07:34 AM: these turned out perfect! ready to blast and paint

(http://forums.trx250r.org/vbulletin_imports/145_5241_2017-04-18_3428.jpg)(http://forums.trx250r.org/vbulletin_imports/145_5242_2017-04-18_9091.jpg)
Title: Fabrication request
Post by: croat1 on May 02, 2015, 01:35:09 AM: Nice!!
Title: Fabrication request
Post by: KASEY on May 02, 2015, 01:06:52 PM: did the front hub this morning,

(http://forums.trx250r.org/vbulletin_imports/145_5244_2017-04-18_9341.jpg)
Title: Fabrication request
Post by: Pumashine on August 09, 2015, 01:02:10 PM: Another fab task complete for Kasey. I guess wagons are in high demand
(http://i57.tinypic.com/17b7md.jpg)
Title: Fabrication request
Post by: KASEY on August 09, 2015, 04:38:11 PM: great!!! I had a lady call me last week ,, she wants 3 wagons for her grankids for xmas.. I showed her some pictures,, 2 hours later she paypaled me $1600 ,,, before you get all crazy,,, go price a new radio flyer metal made in china wagon,,, they start @$99 and go to $189 ,,, the hardest part is the wheels and tires,, finding a deal that doesn't break the bank,,,,, but man am I having fun!! and I have my own models to showcase them

(http://i1141.photobucket.com/albums/n592/KASEYII/waggon.jpg)
(http://i1141.photobucket.com/albums/n592/KASEYII/f28951cb-a23d-4258-beb3-8316de1212c0.jpg)

(http://i1141.photobucket.com/albums/n592/KASEYII/1025141828.jpg)
(http://i1141.photobucket.com/albums/n592/KASEYII/cade%20wagon2.jpg)
(http://i1141.photobucket.com/albums/n592/KASEYII/cade%20wagon.png)
Title: Fabrication request
Post by: troybilt on August 10, 2015, 11:38:03 AM: To the original posted, a bracket like that to mount lights could be printed out of Nylon 645 bridge material, (once I get the material figured out)...
Title: Fabrication request
Post by: KASEY on September 06, 2015, 02:20:39 PM: (http://forums.trx250r.org/vbulletin_imports/145_6287_2017-04-18_9025.jpg)(http://forums.trx250r.org/vbulletin_imports/145_6288_2017-04-18_5550.jpg)
Title: Fabrication request
Post by: KASEY on September 06, 2015, 02:21:23 PM: kid tested ready for delivery to customer
(http://forums.trx250r.org/vbulletin_imports/145_6294_2017-04-18_831.jpg)(http://forums.trx250r.org/vbulletin_imports/145_6289_2017-04-18_2756.jpg)