Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - 2Nubs

Pages: [1] 2
For Sale - Parts / OEM thumb throttle, ESR cover $35 shipped
« on: December 03, 2018, 05:33:19 PM »
OEM throttle from an 88 as far as I know. It is pretty worn out on the inside, but it actually worked and pulled my 39mm carb WOT. ESR cover. Any of you guys need it for parts or is it worthless?

$35 shipped.

For Sale - Parts / All Balls tie rod kit (52-1011) $60 shipped.
« on: December 02, 2018, 11:16:48 PM »
All Balls tie rod kit. Fits 86-89 Trx250R. Retails for $100. Includes heavy duty rods, rod ends, and all hardware. Looking to get $60 shipped. Thanks.

Lounge / Cleaning your R after a trip... What methods are you guys using?
« on: November 29, 2018, 01:51:00 PM »
What method do you guys prefer for clean up? I'm looking into getting a pressure washer to help with clean up after some of these muddy rides and am curious of what others use.

Most of you dune guys probably don't have to use very much elbow grease lol, but here in Alabama it get's nasty during the colder months. Hand washing was a 2-3 hour job last time and honestly it keeps me from casual riding after it's clean. After that much work I don't want to get it nasty again for a trip around my property.

For Sale - Parts / Hiper CF1 REAR 10" beadlocks $250 shipped
« on: November 13, 2018, 04:48:51 PM »
Like new. Single locks. Red rings. 10" diameter, 9" width. These wheels held air for months before I took the sand tires off. Zero leaks, zero stripped hard ware, zero issues. Like new condition. I am only selling so that I can turn around and buy 9's.

$300 and I will ship on my dime. I will send detailed pictures to anyone that is interested. Thanks guys.

Wanted / WANTED: FourWerx "scooped" carbon hood
« on: October 18, 2018, 10:02:33 AM »
Just seeing if anyone has a used one they would like to get rid of before I drop $200 on a new one. Thanks guys

For Sale - Parts / FOR TRADE: Hiper CF1 10" rear wheels trade for 9"
« on: October 17, 2018, 01:57:08 PM »
Long shot I know, but figured I would try it before selling. I have TWO 10" diameter 9" wide Hiper Carbon CF1 wheels in excellent condition. No spun riv nuts or any gimmicks. Used in the dunes four times is what I was told.

I would like to have 9x9's for more dirt tire options. If you are interested just let me know and I'm sure we can work something out. Thanks

For Sale - Parts / SOLD!! Alba Racing nerfs w/heel guard (any year TRX)
« on: September 06, 2018, 01:15:21 PM »
Alba raw aluminum finish nerf bars with heel guards and red nets. Extra wide "pro pegs" and hardware for any year trx250r. They may have some scuffs or dings here and there but they are nice and not very old. All hardware, plus spares, included. You will need to use your peg mount bolts if you have an 86 model and drill a hole in the Alba supplied peg stub.


The Mad Scientist / Durbin Machine wp hose barbs and AN fittings
« on: September 05, 2018, 12:27:19 PM »
This place makes some cool parts for the R's. He has clutch parts that are no longer made and also makes water pump hose barbs in several colors. They also make these barbs with an AN male fitting. I use AN's at my radiator and love to use them anywhere I can on other projects. Just figured I would let you guys know if you did not already.

I could not find these listed, but he responded quickly and sent me a pic so if you are looking for something you do not see send them a message.

Looks good and works great, but it will not fit my new 86 frame without drilling a new hole. One half inch bit of the LED rubber coating is peeled up. Could be super glued easily. All LED's work fine as is. Flag pole mount included.

$50, buyer pays shipping. I can use my company account for a discounted rate.



For Sale - Parts / OEM/PEP rear shock SOLD!
« on: August 24, 2018, 03:24:11 PM »
I believe this to be an 86. I will verify the length. Was told it was built by PEP. I would have it checked out before using.

$100 plus shipping via company account (discounted rate)

I will get better pics once I'm back at the shop.

For Sale - Parts / L/H switch (lights, engine on/off) SOLD!
« on: August 22, 2018, 10:37:32 AM »
New. Never plugged up. Tec L/H switch. $50 shipped.

Wanted / WANTED: bottom engine mount BOLT & NUT
« on: August 07, 2018, 10:18:48 AM »
I need the long bolt and nut that goes through the bottom frame mounted tabs and the engine case.

Number 18 in the diagram. Thanks

For Sale - Parts / ESR reed block SOLD!
« on: August 02, 2018, 03:35:25 PM »
Needs petals. Otherwise looks great. .350" flange.

I'll post a pic after work. Red in color. $75 to your door. Thanks

Projects / 2Nubs's boondock build
« on: August 02, 2018, 11:28:36 AM »
Been getting some good help from several members here. Think it might be helpful for me to make my own thread and maybe cool to look back on one day and see where I started.

Most of you know the run down. Bought this and afterwards realized the frame was junk. Its completely disassembled right now so of course I found things that should be fixed before re-assembly. Hopefully I can have it back going in a week or so. I've not even put a tank through this thing, but I can honestly say I know it from top to bottom and side to side. Everything is getting a good cleaning as well. Sand gets into everything!

1986 250R, Washington title.

ESR 330, pump dome (100 octane, Klotz ST)
ESR 39mm PWK (185 main, CGJ 2nd clip, 48 pilot)
ESR airbox eliminator/intake, UNI/Outerwear
ESR Trx9B center mount pipe/silencer
CR250 ignition
ESR coil mount
ESR ignition adaptor plate
VForce 3
AFCO big radiator w/AN connections (Engine Ice)
ESR water pump cover
ESR shifter and brake pedal

Lonestar +2+1 A arms w/ Moog upper/lower ball joints
Lonestar '86 swingarm -1 (18.5")
Lonestar Axcalibar axle
Lonestar billet sprocket hub
Lonestar forged carrier
Lonestar billet wheel hubs
88/89 spindles
NOS front calipers
Riptide rotors
Works triple rate front shocks
OEM revalved rear shock

Maier plastics
Alba bumper
Renthal 787's and clamps
ASV levers
ODI grips
TM Designworks slide N guide
DID 520 x ring

Hiper CF1's 10x5, 10x10


Wanted / WANTED: 86/87 Frame
« on: July 25, 2018, 10:47:25 AM »
I'm in need of a frame. 86 or 87 will work. I prefer gusseted and powder coated, but will look at all options. Thanks

Pages: [1] 2