Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Topics - jcs003

Pages: [1] 2 3 ... 5
Wanted / TRX250r Rad Valve
« on: June 08, 2019, 09:21:42 AM »
I am looking for a 250r rad valve.  not a cr250 type.

Let me know what you have.

Thank you.


Administration/Moderator Questions / PM Box Structure
« on: January 23, 2019, 11:53:01 AM »
can the PM structure be changed?  It is set up in an odd way that resembles a standard thread.

Thank you,


For Sale - Parts / Engine for sale.
« on: January 18, 2019, 06:51:27 AM »
I am selling an engine.  asking $1,000 shipped

-86 cases
-trail ported
-2001 cr ignition
-+4 crank (porting to match)
-Neil clutch mod
-polished side covers and cylinder.


-bored/honed and piston.
-I would also replace the base studs.  showing signs of corrosion.

Will come with 3 A/S and all replacement gaskets.

Let me know if you have any questions.

Wanted / Silencer
« on: September 12, 2018, 02:09:04 PM »
I am looking for a silencer cheap.  Let me know what you have.

Thank you,


Wanted / 310 stroker cylinder
« on: August 15, 2018, 01:59:48 PM »
I am looking for a big bore stroker cylinder.  +4 to be accurate.

let me know what you have.

thank you,


Lounge / Street Legal ATV
« on: August 07, 2018, 01:14:53 PM »
This seems rather interesting:


Lounge / ESR - Sale
« on: August 03, 2018, 09:23:38 AM »
Cylinder kits are on sale over at ESR.  Big discounts.


Lounge / ATV Storage
« on: June 26, 2018, 07:55:36 AM »
I am looking for an ATV shelf of sorts.  something like below.  I cannot seem to find a manufacture and i have done cost analysis to make my own from metal.  considering aluminum tube, 80/20 and steel.  seems there is no inexpensive solution.  i assume one of these in the image would be more cost effective.

does anyone know a manufacturer of these or a suggestion for a more cost effective solution?

Thank you for any help.


Lounge / DIY epoxy floor coating
« on: May 23, 2018, 08:15:30 AM »
I am in the mdist of a DIY garage floor epoxy coating.

so far I have done the following:

- pressure washed
- cleaned with concrete cleaner and a brush.
- chemical etched
- cleaned and etched again

left to do:

- dry brush
- vacuum
- apply epoxy
- apply clear coat epoxy.

then I will move over to the other side of the garage.  this is the kit i used:

pics in its current state:

Wanted / Head Nuts
« on: May 10, 2018, 05:17:58 AM »
I am looking to buy a set of head nuts.  anyone have a nice, spare set?

The only place on ebay that has them is big dog turds.


Lounge / Cool Builds
« on: May 03, 2018, 01:44:57 PM »

Carburetor, Intake, and Exhaust / 36mm PWK Jetting
« on: March 19, 2018, 02:12:12 PM »
does anyone have ballpark/baseline jetting for a 36mm carb?  specifically, a 36mm pwk.

thank you,


Lounge / Airless ATV tires
« on: March 06, 2018, 02:05:56 PM »
check these out:

i don't see them in common sport ATV sizes.  I would be curious to try them out.


Pages: [1] 2 3 ... 5