TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 2ndmoto

Pages: [1] 2 3 ... 30
1
Carburetor, Intake, and Exhaust / Re: Runs like choked all the time
« on: August 08, 2020, 09:44:28 PM »
Sounds like air issue or a rich issue. Reeds good? Air filter clean? Air box lid on? What jetting you running now?

2
Duner / Re: 2020 Winchester 250r meet up.
« on: August 04, 2020, 09:20:30 PM »
I'll be there...in spirit. Throw a little sand for your homies

3
Suspension and Chassis / Re: Shock rebuild
« on: August 04, 2020, 09:18:25 PM »
I expect a full race report after Winchester

4
Suspension and Chassis / Re: Shock rebuild
« on: August 03, 2020, 07:36:57 PM »
Rebuild or revalve?

5
Duner / Re: 2020 Oregon Dune Adventure
« on: July 30, 2020, 10:14:58 PM »
Just a place to wash off the sand and take a shower would be pretty sweet

6
Duner / Re: 2020 Oregon Dune Adventure
« on: July 29, 2020, 09:23:04 PM »
Dune access is mega baller. Could go in with some friends and buy it. Rent it out when not in use. Could possibly pull a profit. I think UPP and fullbore have some dune access properties

7
Duner / Re: 2020 Oregon Dune Adventure
« on: July 28, 2020, 08:01:38 PM »
Starts at $290k. That's lunch money for most of you

8
Duner / Re: 2020 Winchester 250r meet up.
« on: July 27, 2020, 10:36:29 PM »
I'm crying over here. I hope you all have a good time and everyone it's safe. Hope you guys post a lot of pictures

9
Duner / Re: Silverlake 2020
« on: July 27, 2020, 10:32:12 PM »
Nice. That's really cool to see.

10
Lounge / Re: oxy acetylene
« on: July 24, 2020, 10:01:34 PM »
Was able to cut it . Did this a few weeks back. It took quite a bit of heat. Now I need to get the pin end out of the clevis. Unfortunately the backhoe did not catch on fire, so have to continue to work on it


After all that, it would cost too much to fix the shafts. Ordered 2 new shafts and 2 new caps. New front main seal, rebuilt the injectors pump and hydraulic pump. New water pump and alternator.

Going to try and drill the rest of the pins out this weekend

Thanks Norm for the assist!

11
Duner / Re: 2020 Oregon Dune Adventure
« on: July 23, 2020, 09:27:03 PM »
Sounds like a good time.

12
Engine and Bottom End / Re: HPI VS stock
« on: July 23, 2020, 09:17:01 PM »
To add, You might have run the float bowl dry which would cause it to lean out. When doing hill climbs, the gas will be towards the back of the bowl, which makes the Venturi effect less effective on pulling gas through the main jet

 Any one else running klotz at 40:1? I honestly don't know much about the product. Probably over 20 years ago since I ran it

If you can't catch your finger nail on the scratches on sleeve, have Arlan check it. You might be able to hone it and be on your way.


13
The Mad Scientist / Re: Engine cases
« on: July 22, 2020, 07:22:11 PM »
Hopefully they add some fillets to those outside edges. Regardless it is great to have options for cases

14
Carburetor, Intake, and Exhaust / Re: AAEN pipe
« on: July 17, 2020, 10:32:27 PM »
When Swapping pipes out, make sure to recheck your jetting

15
Projects / Re: LRD Attitude build
« on: July 09, 2020, 11:12:27 PM »
Post some pictures of that swing arm when you get it. It looks interesting

Pages: [1] 2 3 ... 30