TRX250r.org

See likes

See likes given/taken


Your posts liked by others

Pages: [1] 2 3 ... 10
Post info No. of Likes
Gears on ESR site Has anybody noticed Eddie is selling trans gears. From the discretion that's what I think they are.
http://www.eddie-sanders-racing.com/product_p/gears.main.shift250r.htm

http://www.eddie-sanders-racing.com/product_p/gear.set.counter.shaft.250r.htm

December 08, 2017, 03:03:53 PM
1
Re: BOF build Done ready for the first trip


February 16, 2018, 04:33:20 PM
2
Re: WTB: grommets Joe I'll see what I have in my boxes of goodies

March 02, 2018, 06:01:14 PM
1
Packard built pilot 250r motor.(Sold) Listing this for my cousin. It is a pilot cylinder Packard motor. It is a strong running motor. Just more than what my cousin is looking for. I will try to get exactly bore and stroke dimensions. It will be just the motor. It has a hinson basket. Custom boysen rad valve. Low hours 2 dunes trip on motor. No stator flywheel or carb. 2000 shipping not included

March 07, 2018, 02:53:15 AM
2
Re: starting my build Haha that's funny right there. I don't care who you are
March 07, 2018, 08:35:22 PM
1
Re: Packard built pilot 250r motor. The guy I bought it from. Had it built around 2000. He took it down to the dunes on one trip. His back went out getting it out of the trailer. They had to pull start it. He put about 4 hrs on it. Got back and that motor got put on the shelves. 16 years later he offers it up to me in a 89 roller. I buy it. Then my cousin see's it in my garage. Asks what my plans were for it. I was thinking about parting it out. He asked to buy it. So I sold it to him. So we start putting to get her the rest of the way. Ended up having to take the top end off to fix air leaks. It has a 85mm piston. Not sure on stroke. Didn't have my calipers out there when we were putting back together. But we took it out for it's maiden voyage president's Day weekend. Thing runs awesome. It's a torque monster. But my cousin realized its more than what he is wanting. He didn't think it would have as much as it did. So now for sale to do something different.
March 08, 2018, 05:17:16 AM
1
Re: starting my build Get a cr250 intake boot that should put it close to what you need.
March 13, 2018, 02:30:48 PM
1
Re: starting my build I think around 99 to 01. You might have to cut the snuffer off it. I have a Cr reed and boot setup and you have to run a reed spacer to get the alignment right. I do believe mine is a 99. It has the snuffer built into the intake. I'll get pics when I get home.
March 13, 2018, 04:40:19 PM
1
Re: Gears on ESR site
I spoke to Eddie and he tells me these gears are the same ones LED and Schorr is selling.  As of now he only has the counter shaft set in stock.  3-4 week lead time for the main shaft.  Saw the thread on the other site about him being hard to get in touch with.  I know he is busy, but has always gotten back to me.
it is someone over there just trying to make Eddie look bad. Eddie has always returned my emails. It can be hard at times to get him on the phone. Maybe he has caller id and doesn't like the name he sees on it when matuus calls haha

March 14, 2018, 03:33:47 PM
2
Re: 2018 Winchester 250r meet There are hotels right in reedsport. Best western is were we stay usually

March 24, 2018, 10:28:00 PM
1