TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - F-Red

Pages: [1] 2 3 ... 49
1
Suspension and Chassis / Re: Swingarm Skid plate
« on: April 11, 2020, 01:54:26 PM »
Thank you Joe.  ;)

2
Suspension and Chassis / Re: Swingarm Skid plate
« on: April 08, 2020, 05:49:58 AM »
Thank you for the measurements. Much appreciated.

3
Suspension and Chassis / Re: Swingarm Skid plate
« on: April 07, 2020, 07:45:05 PM »
Fred what about some spacers all the way around for a little extra clearance?

Hey Jared. Iím trying to keep the plate as close to the swing arm as possible.

I'm a similar issue. I have what I remember as an '86' custom +4" Lonestar swing arm that I want to add a skid plate to. I will need to cut out the chain area to clear the TM chain guide/follower, but have not found a '86' skid plate to measure to be sure. I could measure my swing arm to give you an idea on what the measurements are, I believe it's an '86'
Let me know
desertR

I would appreciate that. I assume Lonestar had the same location mounts.

I have a custom fabricated swingarm on an 86 and if I recall correctly there are spacers in the front area.im heading to my garage now so I can take a look

Thatís what I did. Mounts flush to the rear mounts (No Spacers). In the first picture, youíll see the results in the front mount. Over an inch gap. More than I desire.

4
Suspension and Chassis / Re: Swingarm Skid plate
« on: April 07, 2020, 02:28:23 PM »
Thanks Joe. I've been talking to XFR Fab in Utah. These are their pics. They do represent the correct year to pic. They say each are unique.

5
Suspension and Chassis / Swingarm Skid plate
« on: April 07, 2020, 01:35:34 PM »
I hope everyone is healthy and staying safe.  ;) I need some help. I recently installed the 86 dog bone and rear shock linkage, to my 88 frame. The purpose was to lower the rear, which it did nicely. I knew the 88 swingarm skid plate would not mount up, because of the lowering of the shock. The 86 plate has the extra clearance for the shock, but the mounting holes are in a different location. Does anybody have an 86 swingarm, that can get me some mounting hole X & Y dimensions? What's different about the 87 swingarm? When you buy the plates, they comes as 86 only, 87 only and 88-89. I appreciate any info. Thanks.


6
Projects / Re: My cry once going big puma build
« on: July 21, 2019, 04:31:37 AM »
You can post pics from you camera roll. Use the reply button, not the quick reply.

Just a test. Iíll delete the pic. Donít want to contaminate your thread.


7
Engine and Bottom End / Re: Ignition wire grommet
« on: July 21, 2019, 04:14:04 AM »
A .50 grommet not included? What the what? As Gene said. McMaster-Carr should have what you need. 

8
Lounge / Re: Tinypic
« on: July 21, 2019, 04:06:00 AM »
Posting from the iPad, you have the option to add a pic from your camera roll.


9
Projects / Re: 86' full build
« on: July 20, 2019, 07:06:48 AM »
Sweet ride. I have two CCP steering stabilizers. Iím very please with their performance.

10
Engine and Bottom End / Re: 1986 radiator hoses
« on: July 01, 2019, 08:22:13 PM »
Congrats on the renovation. A simple upgrade can turn into a snowball. Well worth the effort and money when completed. Self-Gratification! If I remember correctly, I think some guys just manipulated the available hoses on the radiator nipples. Do a search, you find some info. Good luck.


11
Engine and Bottom End / Re: 1986 radiator hoses
« on: July 01, 2019, 07:04:34 PM »
Welcome to the site. Those eBay guys have always listed those hoses in error. I have an 88 so those listed work for me. Someone here will be able to help.

12
Lounge / Re: Honda's Legendary Status!
« on: June 26, 2019, 10:02:19 AM »
Oh Memory Lane Joe.

Post some pics Myles. Love this little bikes.

I want this puppy!

13
Lounge / Honda's Legendary Status!
« on: June 24, 2019, 06:43:30 AM »
Over 100 million sold, in the world! Just another example of Honda's extraordinary excellence. 

The Super Cub.


14
Carburetor, Intake, and Exhaust / Re: UPP Intake Boot Ripped
« on: June 19, 2019, 03:13:58 PM »
Leave it to Jerry to go the extra effort and BLOW our minds! Can we assume, Sonny's billet intake would be the answer?



15
Carburetor, Intake, and Exhaust / Re: UPP Intake Boot Ripped
« on: June 17, 2019, 06:45:55 PM »
This is for you Myles. The pic is a little misleading. But there is a significant difference.



Pages: [1] 2 3 ... 49