See likes
See likes given/taken
| Post info | No. of Likes |
|---|---|
Re: Rebuild LSR/HOUSER
On another note....what does that white LSR look like nowadays? 
April 20, 2018, 12:21:18 AM |
1 |
Alternative rear MC push-rod
Just finished rebuilding a complete set of brakes to replace the tired, butt dragging 32 year old originals on my R. All the zinc was gone from the push-rod I was going to use & there discontinued so after talking to @hawaiiysr he steered me toward Suzuki. We have an 87 LT230 & it looked to be pretty close so I ordered one for that. I think the LT250 & Zilla also used the same rear push-rod in the same era so one could be ordered for any one of those LT's & it will work on the R rear master. The part number for the one I got was 69670-00A00. Above the seal groove all the dimensions are within a few thousandths so there a direct replacement. I used a Shindy rebuild kit for the R master with the LT push-rod & it fit together like it was OEM. The LT rod is about 1/4" longer than the Honda rod so it will probably need to be shortened to keep the brake pedal in the right spot with OEM pegs & pedal... Also for the front master cylinder there was a kit shown specifically for the 86 & than a kit for the 87-89. The 86 kit was in the $35-40 range but I got the $18 87-89 kit anyway & it was identical in every way to the guts I pulled from the 86 front master I used for the rebuild:     June 26, 2018, 03:14:04 AM |
1 |
Re: 2018 Winchester 250r meet
 If you see this stop and say hello August 16, 2018, 08:41:07 PM |
1 |
|
Kick starter shaft shims 85-86 250r
If anyone needs the 2 shims for their 85-86 250r kick starter shaft . Order Honda part number 90554-728-940.Same as number 10 in pic.
September 05, 2018, 07:43:23 AM |
1 |
Re: ESR QC cover
Looking even better on the motor
September 08, 2018, 06:34:27 PM |
1 |
|
Re: Tie rod recommendations
Txt me the bushing dimensions Steven & I'll make some for you on the lathe. I got stainless, mild steel & aluminum on hand.
September 19, 2018, 11:30:10 PM |
1 |
Re: 2018 Winchester 250r meet
How big is the dune area at Winchester? If you're coming that far, plan to stay a week and also ride the other dunes (Winchester Bay has Florence riding area 30 min to the North and Coos/North Bend riding area to the South). Here's a link to the Forest Service's map of the OHV areas: https://www.fs.usda.gov/Internet/FSE_DOCUMENTS/stelprdb5259370.pdf October 09, 2018, 12:18:47 PM |
1 |
|
Re: 2Nubs's boondock build
Still fine tuning the carb. I will most likely be looking for a new cylinder to have ported for low end or possibly find one to trade mine for. As much as I love the hit I need something more friendly for the tight woods. I'm going to see how I feel about it after a trip this Thanksgiving. I've installed an OEM coolant tank, OEM rad shroud brackets and a TM Designworks frame pad. Fixing my rear brake and buying tires are the two big things I need to get done. The rest is pretty small. Here's a pic I took while riding yesterday. 
October 10, 2018, 10:34:42 AM |
1 |
|
85 take out cases
As stated...85 take out cases. Not the best finish on the cases (need powder, paint or polish) but they are 85 take outs. $475 shipped. Price covers shipping and fees. SOLD Joe November 29, 2018, 12:23:37 AM |
1 |
Re: Coops woolly booger.
Funny thing about his R is it had some old woolly booger tires on it when I bought it. We named it the "woolly booger " 
May 15, 2019, 08:33:04 PM |
1 |
