TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - zcarlson12

Pages: [1] 2 3 ... 44
1
Suspension and Chassis / Re: HRE ATV
« on: March 31, 2025, 09:15:45 AM »
Thanks Joe. I don’t know why it doesn’t let me post sometimes. Maybe the file is too big?

2
Suspension and Chassis / Re: HRE ATV
« on: March 03, 2025, 09:03:39 AM »
Here you go sir.

3
Engine and Bottom End / Re: Rekluse clutch with ESR cover
« on: February 25, 2025, 06:26:47 PM »
Not yet, to the best of my knowledge he hasn’t released them to the public yet. I am interested though.

4
Suspension and Chassis / Re: HRE ATV
« on: February 20, 2025, 11:57:55 AM »
He’s made a bunch of them and from what I can tell it’s exactly like my Laeger one. I got a billet linkage from Phil Denton Engineering out of the UK. Very nice piece. I know Steve at ISF Racing makes them but I didn’t want to wait and I’m sure his are nice as well. No info on progression rates or anything that’s just what my frame was built for.

5
Engine and Bottom End / Re: Cp industries 250R lynx cylinder
« on: February 20, 2025, 05:09:54 AM »
They don’t allow quads anymore unfortunately. Major bummer because that was my hometown track.

6
Engine and Bottom End / Re: Rekluse clutch with ESR cover
« on: February 19, 2025, 01:12:25 PM »
I can’t get the other pics to upload I guess the file is too big.

7
Engine and Bottom End / Re: Rekluse clutch with ESR cover
« on: February 19, 2025, 01:09:41 PM »
2

8
Engine and Bottom End / Rekluse clutch with ESR cover
« on: February 19, 2025, 12:58:15 PM »
After my last ride I thought something was going on with the clutch and I had to replace the mechanical water pump seal anyway so I pulled off the cover to find 6 of the 10 basket finger sleeves broken. They were catching on the QC cover. Just in case someone else is running or wants to run this setup be aware.

9
Suspension and Chassis / Re: HRE ATV
« on: February 19, 2025, 12:28:52 PM »
He just built me a cr500 link swingarm. Still in business and in my opinion he did great on my swingarm.

10
Engine and Bottom End / Re: Cp industries 250R lynx cylinder
« on: February 19, 2025, 12:27:21 PM »
I’m running a Lynx. Love it on the mx track.

11
Lounge / Re: Parts washer/ultrasonic cleaner
« on: December 15, 2024, 08:27:13 AM »
I use my ultrasonic to clean air filters now. Bought this stuff and haven’t looked back. https://www.nashsolutions.com/

12
MX / Re: Briarcliff MX
« on: October 08, 2024, 09:41:50 PM »
I bought the engine second hand honestly ready to go as a package but I believe it is a 380 CPI Lynx ported by Dave Moore, 350G pipe, 39mm PWK, Vforce reeds, Zeeltronic ignition, LED intake with Uni filter, Rekluse clutch. Been running 15/38 gearing and love it. I’m sure you all know but Dave is a great guy and literally just got off the phone with him tonight about the clutch and how to move forward. I’ll know more when I pull the cover but I have one of his adjustable clutch lifters to try If the clutch pack looks good.

13
MX / Briarcliff MX
« on: October 07, 2024, 08:32:06 AM »
Went to Briarcliff mx for the Digging Deep ATV Podcast ride day over the weekend. Had a great time and the track was mint. One double to flat I wasn’t hitting because I had overshot it earlier and it did not feel the best haha. Also may need to check my clutch, seemed like it wasn’t pulling like it normally does but was making lots of noise. Enjoy

https://m.youtube.com/watch?v=nioTgXkSmog

14
MX / Re: Pusheta Creek MX
« on: September 05, 2023, 08:39:32 AM »
Made my way out to this place again. Caught a couple of my better laps from the GoPro, enjoy.

https://m.youtube.com/watch?v=_xosFmC7lbI&pp=ygUScHVzaGV0YSBjcmVlayAyMDIz

15
MX / Re: TX MX national 2023
« on: April 25, 2023, 01:03:51 PM »

Pages: [1] 2 3 ... 44