TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - xTHUNDERCATx

Pages: [1] 2 3 ... 8
1
Drag Racing / 250r Shootout pismo dunes
« on: August 02, 2016, 10:04:03 PM »
I doubt I'll be dusting the 250r off until halloween. Makes me jealous as hell.

2
Engine and Bottom End / Leak around cylinder base
« on: July 17, 2016, 11:23:00 AM »
I'd build a leak down tester to verify what going on and when it's fixed. Simple insurance to keep the motor from burning down from an unkown leak.

3
Drag Racing / 250r Shootout pismo dunes
« on: July 06, 2016, 03:27:55 PM »
not that I saw, I'm assuming its run what you brought heads up hill racing.

4
Drag Racing / 250r Shootout pismo dunes
« on: July 06, 2016, 12:34:21 AM »


I'm not associated with the people putting this on, but I saw it on facebook and figured I'd post it up over here.

5
Lounge / West coast 250r meet up
« on: May 22, 2016, 04:35:32 PM »
Yep, the shee is ready and the r should be running for this one just need my shocks rebuilt. I'm trying to get brandon to head out too.

6
Lounge / West coast 250r meet up
« on: May 22, 2016, 03:19:47 PM »
I'll be at sand mountain for halloween If everyone that is talking about it heads out there it should be a pretty big weekend.

7
Duner / Anyone going to Dumont dunes this coming Halloween weekend 2015
« on: September 23, 2015, 05:41:11 PM »
That's a bummer, I'll be heading out for the weekend but I don't know if the R is coming. Were bringing the drag banshee down to run the hill.

8
Lounge / First 250r, and new to forum, Props to ESR!
« on: April 22, 2015, 08:44:19 PM »
Those are both good looking bikes, When I'm back home If I remember right I'm jetting in the 162ish range with a 38 airstryker, trx11 and some form of chicken scratch port. Just to give you an idea so if he puts you anywhere  near that I would guess you would be well on the safe side considering I foul the occasional plug.

9
Engine and Bottom End / Need port work and head cutting who to use?
« on: March 29, 2015, 10:24:38 PM »
May have a tough time with Wildcard. I need to sweet talk him just to get him to work on my banshee he built. Thats interesting I have seen a couple of redline's bikes run and the few I did see ran hard, I actually wanted to take the dune bike to him if Brandon isnt able to do it. But I don't have first hand experience with Redline so I'd take Russell's advise over mine Sangheraent.

10
Engine and Bottom End / Need port work and head cutting who to use?
« on: March 29, 2015, 06:34:32 PM »
Just a side question what actually makes you say it was built like garbage? If you want local I wouldnt hesitate to go with redline, if not Neil (C-Leigh racing) would be my first choice for a bottom end motor.

11
Engine and Bottom End / Pro x cylinder
« on: March 28, 2015, 02:56:37 PM »
I think ESR sells them.

12
Duner / can't wait heading to dunes 21 and 22
« on: March 22, 2015, 01:30:38 PM »
How did you end up breaking the collar bone?

13
Duner / Pismo for spring break first weekend of april
« on: March 03, 2015, 11:56:05 PM »
How often do they run at the river bed?

14
Engine and Bottom End / son of a b!#$%
« on: March 03, 2015, 10:13:42 PM »
Your looking at the cases, but you said they were new bearings, where did you get those, what if its the bearing tolerances that are bad?

15
Duner / Pismo for spring break first weekend of april
« on: March 02, 2015, 08:23:24 PM »
that would be cool, I'm still working out what ill be doing, the R is down, I am hoping to get the drag banshee motor done this weekend but I dont think I'll be able to get a arms for the new frame. I may end up just bringing out the dune banshee to play on. Also if I make it and anyone happens to run klots techniplate full synthetic (not the super techniplate) I have 5 quarts that I would sell dirt cheap or pretty much trade for a coke. I ordered them by mistake and they have been sitting on the trailer since.

Pages: [1] 2 3 ... 8