Messages

1

Projects / Newbie 1989 trx 250r project

« on: July 25, 2016, 01:42:42 PM »

Glad ya got it figured out gregg. Those aftermarket  cdi  boxes are hit or miss sometimes causing kick back or spark issues or work fine. I would try it an not let it sit as a back up so you can send it back. Everyone perfers oem cdi.

hey rich i actually used the stock oem cdi it was good after all was said and done.
As a footnote to this project i coild have never fiinished it without your help, i appreciate your many texts and parts, guidance and just general help, thanks much sir!
next is bleed brakes, change out pads front and rear, install fresh brake fluid, nerfs, and fasten shock rese's on front of frame
, some jetting as well and new air filter.
Is there any guidelines here on setting the front end using the Lonestar +2 a arms?

2

Projects / Newbie 1989 trx 250r project

« on: July 25, 2016, 08:54:13 AM »

thanks i actually did that mod and wrapped with header wrap as well.
finally got  the spark to work, had to take the harness apart and re wire it����ordered a new repro off ebay to replace it in the future.
after getting spark i actua)y finished up the other little items pit the plastics on and did some compression checks, etc got 198 psi

3

Projects / Newbie 1989 trx 250r project

« on: July 22, 2016, 10:15:14 PM »

With the 88 89 radiator and lrd pipes your pipe and coolant line will rub.

Thanks, any tips or methods to avoid burning the line? Project on its wheels off the work horses, all together but need help on 1 item, I can get any spark, checked  everything, used my fluke meter for pulse generator, alternator, cdi, all the electrical components. They all checked in within tolarances. I had 1 question, I do not have the stock ignition switch, the previous owner has cut and spliced the living hell out if this harness I do have a tether switch on the bars, were does the wires off that go?

4

Wanted / WTB 88 trx 250 items

« on: July 17, 2016, 02:42:38 PM »

What size front tires / rims ?

What size rims do i need to use with the lonestar +2 arms, the offset should be different then stick correct?

5

Wanted / WTB 88 trx 250 items

« on: July 17, 2016, 08:37:57 AM »

I have most of what your looking for....I'm not going to have the mount for the radiator hose or the switch assembly...I'll PM you my number so you can text me....Jeff

Jeff any idea on your parts? Would rather purchase off the board them other sources. Thanks

6

Wanted / WTB 88 trx 250 items

« on: July 17, 2016, 08:36:54 AM »

Just saw these on ebay: http://www.ebay.com/itm/1988-Honda-TRX250R-Footpegs-/272309788974?hash=item3f66eda12e:g:2XcAAOSwdzVXikAS&vxp=mtr

Git them thanks, and thanks for parts they worked well indeeed.
Still need some items
Rear brake lever with hardware
On/off switch headlight on/off assembly for handlebars
Rear tail light.

7

Wanted / WTB 88 trx 250 items

« on: July 05, 2016, 01:42:32 PM »

Stock, anythong up to a 21 i am open too.

8

Wanted / WTB 88 trx 250 items

« on: July 04, 2016, 09:27:58 PM »

Looking to purchase the following items for my project:
Kickstarter
Snap ring for excalibur axle, stock is fine according to excalibur to tighten brake hub.
Foot pegs, used, new, aftermarket, open to all
Handlebars for  LSR 1 1/8 ANTIVIBE , used new , open to all options
Grips for handlebars-vendors that sell them would be huge help
Lid for coolant overflow tank, will buy complete unit if needed.Used good here as well
2 upper tie rods for +2 Lone star a arms to fit 88 spindles.
Engine off/on lights on/off assembly for handlebars, used fine.
Rear brake foot lever, need hardware with it too please.
Mount for frame to keep coolant hose away from expansion chamber on right side of frame.
Air box rubber hose clamp, big clamp by air box
Intake clamp for carb to intake.
2 front rims and tires, preferred 190's alumn used or new good here as well.

9

Wanted / WTB: OEM Gold Wheels

« on: July 04, 2016, 09:17:14 PM »

I think I have a set off a three wheeler, they the same? rears they are. Probably 86 or 85's

10

Projects / Newbie 1989 trx 250r project

« on: July 04, 2016, 09:13:11 PM »

Ok project has basicly been completed, but I need a couple items for it:
Kick starter
snap ring for the excalibur axle, stock is what they say fits
Foot pegs
2 upper tie rods for +2 Lone star a arms, the ones that came with it do not fit the 88 spindles. Vendors that sell would be a huge help to me for this!
And finally handlebars, never got them, got 1 1/8 anti vibe LSR on the stem,any ideas are greatly welcomed for this!
Engine off/on, lights on/off full assembly, mine is toast and needs to be replaced-used is fine!
Mount that goes to the frame on the exhaust side that keeps coolant line away from the pipe.
Anybody have these items please PM me, and thanks for all the help-

11

Wanted / WTB 89 trx rear shock parts

« on: May 01, 2016, 03:31:16 PM »

Purchase from schmidty, good deal, was my pleasure.

12

Wanted / WTB 89 trx rear shock parts

« on: April 27, 2016, 01:11:40 PM »

Thanks forbthe links wil purchase off the site vendor.

13

Wanted / WTB 89 trx rear shock parts

« on: April 26, 2016, 05:25:50 AM »

Yes I have it dis assembled currently and are rebuilding it. Do the rebuild kits come with a new bump stop? I have already replaced the inner seal with an All Balls one, have the nitrogen kit for refilling, just need the stop, is there a seller here we use for them by chance?

14

Projects / Newbie 1989 trx 250r project

« on: April 24, 2016, 08:47:42 PM »

Thanks for the help, I spoke to a Boyesen rep and they indeed do make a valve for the 34mm stock carb, which is what I will order. I have the rad valve here and the spacer did indeed take all the space out.

15

Wanted / WTB 89 trx rear shock parts

« on: April 24, 2016, 08:31:04 PM »

WTB 89 stock rear bump stop-I am looking for the stock bump stop that slides on the shock shaft to prevent the shock from total compression. My shock is missing it completely.