Messages

1

Duner / Glamis

« on: November 27, 2014, 04:10:00 PM »

Have fun!

2

Lounge / phrase of the day

« on: June 25, 2014, 11:05:38 PM »

"------- is as useless as balls on a dildo"

3

Hybrid 250R / Lt500/250r pipe

« on: June 25, 2014, 09:56:18 PM »

A zilla LRD pipe can be made to fit a trx frame but some fab is involved.

4

Hybrid 250R / Lt500/250r pipe

« on: June 25, 2014, 09:41:25 PM »

Someone bought my led hybrid  pipe......

5

Lounge / whats one of the best tools in your shop?

« on: June 17, 2014, 01:50:10 PM »

Miller syncrowave 250. Great tig for alum or steel.

6

Duner / Winchester Bay with my 4 R's

« on: June 17, 2014, 01:47:00 PM »

Thanks, Maxx
 
 If you still have your honduki frame we may have to talk. How is your bug coming along?

Yep still have the frame tucked away.
Bug is slow going a lot of fab work. Picked up a pinto engine out of a rail for it and a 091 trans

7

Duner / Winchester Bay with my 4 R's

« on: June 17, 2014, 01:22:51 AM »

Lookin good!

8

Projects / Hondzilla

« on: January 18, 2014, 04:39:29 PM »

Arlan, at LED was building one of these for a guy a couple years ago, so you might try him for a pipe??
 Thanks Higgy

That was most likely my bike you saw there.....has had its taste of banshees over the last few years

9

Wanted / Keihin PWK Throttle Valve #6 Slide

« on: January 12, 2014, 05:56:26 PM »

Shit for 80$ I have a 41mm Pwk with a #6 in it for not too much more than that.....well maybe a little more

10

Lounge / Picture of your day!

« on: November 08, 2013, 08:56:07 AM »

[ATTACH=CONFIG]2270[/ATTACH]

Cutting up a new project today

11

Carburetor, Intake, and Exhaust / Petcock mod flow data

« on: October 20, 2013, 02:50:09 PM »

Going from .195" to .235" is an increase in DIAMETER of 20.5%


Going from .195" to .235" is an increase in AREA of 45%



If there are not any restrictions above or below the .235 diameter hole you should have an increase in VOLUME (flow rate) of about 45%.

Running a CR250 petcock that has been drilled out is a cheap mod for those on a budget. You lose the res though.

12

Lounge / Eastwood DIY powdercoat?

« on: October 08, 2013, 07:47:33 PM »

My set up is from caswell plating. Works good for me but sandblasting sucks a$$. I've found to use paint stripper first then follow up with sand or glass bead is the fastest. I use a standard home oven but for longer stuff like extended swingarms I cut a race can sized hole in the door and used a insulated race fuel can to extend the door out. It gets strange looks and comments like what's a can of fuel coming out of your oven for...but it works. For hanging parts, I took one of the extra oven grates and hung it 1" from the top of the oven so hooks and wire are easy to hang. Good luck.

13

LED Performance / LRD TRX 250B Pipes

« on: September 19, 2013, 03:16:15 PM »

Too bad you can't dedicate some stampings for a few zilla pipes. When the LRD pipes surface they don't last long and go for top $. - J

14

Lounge / Anyone out near Boise or Meridian Idaho?

« on: September 15, 2013, 03:04:24 PM »

2 hrs ......

15

Pics and Vids / Well I am gonna start a action pic on your R's

« on: September 15, 2013, 05:05:59 AM »

On my LeD built 535 Honduki.