Messages

1

Lounge / lets see your pets

« on: May 08, 2014, 08:21:16 AM »

My 12 week German shepherd husky
.

2

Lounge / Pic Request: Carbon Fiber Flat Hoods (no scoops) on OEM/Maier Plastic

« on: April 02, 2014, 10:25:16 PM »

He's mine

3

Lounge / Any of you fellow R lovers into old trucks??

« on: April 02, 2014, 10:17:31 PM »

Pretty soon shell be looking as good so the white 79 but for now she's just chilling in the barn waiting for summer.

4

Lounge / Any of you fellow R lovers into old trucks??

« on: April 02, 2014, 06:56:12 PM »

My 1973 k10 soon to be 4 linked with 18in of travel under it

5

Cranked Up Gear / Vote to enter free drawing

« on: March 19, 2014, 02:11:46 PM »

i like #3

6

Duner / july 11-13 2014 silver lake sand dunes

« on: March 16, 2014, 09:17:22 PM »

Can you camp out at the dunes or does it close and need to re-enter everyday?

It closes down every night at sun down and re opens at 9am

7

Engine and Bottom End / Clutch problems!

« on: March 15, 2014, 01:21:49 PM »

Thanks so much!! You have been a huge help! Can't thank you enough!!

8

Engine and Bottom End / Clutch problems!

« on: March 15, 2014, 12:47:13 PM »

It's all back together now I used the second smallest shim. Give me just enough tread on the handle bar and the case mount to have a tight lever with no play. It seems like it won't slip still good pressure on the plates.

9

Engine and Bottom End / Clutch problems!

« on: March 15, 2014, 11:48:14 AM »

Alrighty thanks!! I'll start be doin that!

10

Engine and Bottom End / Clutch problems!

« on: March 15, 2014, 11:28:35 AM »

Is there anyway to tell this before it all goes back together? Or just hit or miss?

11

Engine and Bottom End / Clutch problems!

« on: March 15, 2014, 09:25:48 AM »

Got my shims in the mail yesterday!! Thanks so much pumashine!! Plainin on trying them out today! See if this solves my problem!!

12

Engine and Bottom End / Clutch problems!

« on: March 13, 2014, 02:03:32 PM »

thanks pinned! cant wait till i can no as much as all you guys!!

13

Engine and Bottom End / Clutch problems!

« on: March 10, 2014, 10:01:38 PM »

Well I cant measure mine very accurately, but the three I have, which should be 89 update (roller bearing) sized, and they are barely over 8"
My calipers only go 6" so it was an eyeball on a ruler.
I'd use Tonys numbers if you can measure yours with a bigger set.

Haha I just put two 6 inch calipers together and it measured out to be 8.040 for both of my rods

Sent from my ADR6350 using Tapatalk 2

14

Engine and Bottom End / Clutch problems!

« on: March 10, 2014, 07:21:33 PM »

Being that far into it you should have two flat hardened washers that look similar to the one you pictured. One goes behind the lock washer/tab that holds the inner hub on. #21 in the above diagram. And the one Puma is talking about which goes between the roller bearing and the pressure plate. (which is not shown on the diagram) Its kind of hard to judge the two in the pictures sometimes.
 The pressure plate one, usually sticks behind in there. Just wanted to point out the two of them. They wont interchange because of their size difference.

I also agree your lever isnt that far gone yet to cause this.

So you think its just the rod is too short?

Sent from my ADR6350 using Tapatalk 2

15

Engine and Bottom End / Clutch problems!

« on: March 10, 2014, 06:43:03 PM »

Trying to find a caliper right now. I'll let you no what I come up with thank you pumashine!!!! Been a great help! Really appreciate it!

Sent from my ADR6350 using Tapatalk 2

 

Sent from my ADR6350 using Tapatalk 2