TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Piediddy

Pages: [1] 2 3 ... 5
1
I saw the FB  post, read both write ups and saw pics of both bikes. I voted, then I went back and asked who he was. I wasn't going to say who I voted for and didn't let his FB post have an effect on who I voted for.

2
Drag Racing / Gearing
« on: July 03, 2016, 11:42:51 PM »
Gearing is kinda trial n error, there's a lot to factor in, weight, paddles, length of swingarm etc. I like to set my bikes up to take off in 1st and get the bike out the hole with less spinning and wheeling. A bike with no cut transmission you wanna gear it for less shifts but a good combination of hole shot and topend. Adding teeth to the front sprocket does the same as less on the rear sprocket.

3
Pics and Vids / Packard puma times from the Michigan national races
« on: June 29, 2016, 09:05:22 PM »
Good Job Morse, it sounds good and crisp. You still running the CPI pipe and 48 Lectron? Whoever is riding it is treeing the hell out of the other guys ha

4
Projects / 443 Puma - Dune Motor Build
« on: June 20, 2016, 08:40:00 AM »
What pipe and carb are you gonna run on it?

5
Projects / LSR Titanium Drag Chassis "Super Puma" Update Project
« on: June 18, 2016, 08:57:48 PM »
Love that bike. Use to be Duners and he sold it to William. Who owns it now? I saw videos of it eating 10Mill Banshees up.

6
Engine and Bottom End / CP vs Pro X cylinders?
« on: May 14, 2016, 08:22:45 PM »
I wouldn't put an OOF pipe on a dune/trail bike. You will be happy with a good inframe.

7
Wanted / Billet Front Hubs - Hardkor, RPM, Baldwin, etc
« on: April 21, 2016, 03:36:56 PM »
And you can't beat $140 with bearings and seals. Different colors too

8
Body and Controls / What Grab Bars Fit TRX250R?
« on: April 17, 2016, 08:50:43 AM »
There is a nice RIS Designs rear bumper on EBay but its for a Raptor 250. I could redrill holes but not sure about the width.

9
Wanted / Brake caliper
« on: April 08, 2016, 02:32:12 PM »
I sent them an email, waiting for a response. I'm looking for a rear caliper also

10
Carburetor, Intake, and Exhaust / ESR 5b
« on: March 06, 2016, 06:12:49 PM »
Yea the stinger does flare to slip over the other pipe. Mine isn't quite as bad but the welds could be a little cleaner. You won't notice it on the bike, I didnt notice it until I read this and went looked at it.

11
Wanted / decent radiator shrouds
« on: March 02, 2016, 05:13:39 PM »
Quote from: Pumashine;65122
I love this pic with the matching stand. I will only build thicker aluminum shrouds .080" thick so they last a lifetime.
Pumashine, do you still make the shrouds with the slots in them? I PM'd you a while back and never heard back.

12
Too Nutz Creations / a powder to match honda gold
« on: March 01, 2016, 05:10:52 PM »
Not gonna get it perfect cause the the original wheels etc are anodized, but I just had stuff done. It's a little darker compared to original but it's the closest powder we could find. Don't know what it's called but it's a 2 part with a silver base. I can text you pics if you want

13
Body and Controls / Difference between 86 & 87 gas tanks
« on: February 29, 2016, 12:42:42 PM »
Aren't the caps different also? Certian year has bigger cap?

14
Wanted / WTB Steering stem and Clamp
« on: February 23, 2016, 08:10:29 AM »
I tolerate you because your Son is my best friend not you. Also I found a stem thanks for your help. Where is my brake stay collar and CR ignition?

15
Wanted / WTB Steering stem and Clamp
« on: February 21, 2016, 06:51:15 PM »
I'm looking for a Chrome +1 stem with 7/8 clamp. Needs to be in good shape. Lemme know what you have. Thanks

Pages: [1] 2 3 ... 5