Messages

1

Engine and Bottom End / esr porting question

« on: September 26, 2014, 05:15:14 PM »

that is a 350 cylinder probably a 78mm thats the first bore, with a 77mm crank which is a +5 making it a 370. the PV11 is esr's 11 porting.

2

Carburetor, Intake, and Exhaust / 110 vs c12 vs oxygenated fuels? what are your experiences/opinions.

« on: September 01, 2014, 02:52:48 PM »

i ran q16 in my 370 and u4.4 they are both oxy fuel

3

Wanted / WTB ESR TRX5 Pipe

« on: May 07, 2014, 01:51:36 PM »

i have a trx5 pipe cm. perfect condition. text me for pics 2083602243

4

Wanted / Wanted a trx5 cm pipe!

« on: February 23, 2014, 10:22:31 PM »

I'm looking for a trx5 centermount pipe in mint condition. shipped to idaho. pm me if you have one thanks!!

5

Engine and Bottom End / PVL Ignitions

« on: February 08, 2014, 06:18:35 PM »

I run a pvl on my 370 duner/hillshooter. I had bad kick back for months and come to find out i had a weak/bad ground. fixed that and i hasnt had a kickback since.

6

Engine and Bottom End / puma ??

« on: December 10, 2013, 10:05:14 PM »

I'm looking only for the motor.
cylinder,piston, dome, reed cage, crank, cut cases.

7

Engine and Bottom End / puma ??

« on: December 10, 2013, 07:04:10 PM »

whats the cost of a 431 puma motor?
as a whole?
as a kit?

8

Lounge / eBay radiators?

« on: December 04, 2013, 10:35:48 PM »

asi performance
they were like 60-70 bucks
andi plan on buying another one for a drag bike im building

9

Lounge / eBay radiators?

« on: December 04, 2013, 10:25:48 PM »

I've got one on my drag 250r and drag yfz450. the welds are good and seem to hold up just fine, the prices are cheap!!

10

Engine and Bottom End / nitrous

« on: December 04, 2013, 10:09:28 PM »

what about jetting? or does the wet kit just blend it so jetting isnt an issue?

11

Engine and Bottom End / nitrous

« on: December 04, 2013, 08:54:48 PM »

what fogger kits are available. and i dont have a battery and dont really want to install one to run a solenoid.

12

Engine and Bottom End / nitrous

« on: December 04, 2013, 07:42:51 PM »

i'm running vp110 fuel
and i was looking at the boss noss kit and i would only do a 10-15hp shot.

13

Engine and Bottom End / nitrous

« on: December 04, 2013, 01:16:15 AM »

Anyone run nitrous on their 250r? What kit works best, this is a hillshooter that it would be going on with a 370 motor.

14

Carburetor, Intake, and Exhaust / pwk float valve seat

« on: November 07, 2013, 07:45:14 PM »

Where can I get a replacement?? I'm looking for a 3.6 I have a 1.8 and its too small its for a pwk 39mm.

15

Carburetor, Intake, and Exhaust / carb sugguestions

« on: November 07, 2013, 02:26:19 PM »

I run a esr11 pipe and I have their trx12 port, I plan on sending the cylinder to Matt shearer to report if needed and going to run one of his oof pipes