TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Tbus93

Pages: [1] 2 3 ... 5
1
For Sale - Parts / Nice 88-89 cases
« on: October 20, 2015, 06:34:23 PM »
Nice set of center cases no damage what so ever $425 shipped text me for pictures 7852153979

2
Wanted / Wtb aftermarket standard travel a arms
« on: August 03, 2015, 10:27:21 PM »
found some courtesy of mandom great seller fast shipping

3
Wanted / Wtb +2+4 axle
« on: August 03, 2015, 10:26:44 PM »
bought one

4
For Sale - Parts / mostly aftermarket part out
« on: July 29, 2015, 03:48:35 PM »
I'll take the bumper

5
Wanted / Wtb +2+4 axle
« on: July 27, 2015, 05:58:54 PM »
Pm me on what you have prefer lsr and chrome

6
Wanted / Wtb aftermarket standard travel a arms
« on: July 25, 2015, 12:36:15 AM »
Laeger or lone star prefer chrome under $300

7
For Sale - Parts / 2001 CR250 Ignition - Complete Setup
« on: July 22, 2015, 06:57:21 PM »
payment sent

8
Engine and Bottom End / Sick R
« on: July 17, 2015, 10:34:52 PM »
I was thinking possibly maybe my stator is goin bad, Possibly needing a reed spacer to antodize fuel better, or it has the wrong piston in it or something idk no clue on this whole ordeal

9
Engine and Bottom End / Sick R
« on: July 17, 2015, 12:53:15 PM »
Quote from: Pumashine;56118
This does not tell us what jets and needles you have tried on the carb if at all.
I've tried jets ranging from 168-184 and two different needles and moving the clips position

10
Engine and Bottom End / Sick R
« on: July 16, 2015, 10:25:11 PM »
Having problems with my R in first and second gear it has no power if you dump the clutch in first it bogs down and all the power turns on in 3,4,5, and 6th I've tried everything I can think of short of pulling the head to look at the top of the Piston but it's ran like this since I had it built. It's a esr 310 with the high compression dome built by a local builder vforce3 reeds without a spacer trx5 pipe 38 as carb short rod crank. His porting notes show .055 squish 196/192 triples 130 transfers from 187/122 just pulling the carb off this thing looks like it's way overported to me if someone can shed some knowledge on what can be wrong I'm about to toss the cylinder in the trash and go back to stock

11
For Sale - Parts / Walsh Chassis
« on: July 16, 2015, 09:47:20 PM »
It should be in my garage just locally picking up means 876 miles away lol

12
For Sale - Parts / Walsh Chassis
« on: July 15, 2015, 05:01:48 PM »
Where is this located?

13
Oops forgot to take wash and take pics of mine

14
Projects / My 89 250r
« on: May 05, 2014, 03:56:09 PM »
Not sure what the paint is on the frame I bought it painted already, and that red Duncan cover is that one that was for sale on here a few weeks ago

15
Projects / My 89 250r
« on: May 04, 2014, 10:25:56 PM »
Esr 310 it runs pretty good

Pages: [1] 2 3 ... 5