TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hurley250R

Pages: [1] 2 3 ... 6
1
Lounge / woke up to this, this morning.
« on: September 09, 2016, 09:07:05 AM »
That sucks! I haven't made it out their in a couple years, hope it doesnt close down. I always heard stories of people drinking and riding at night and getting hurt. Idiots

2
Carburetor, Intake, and Exhaust / Amsoil Dominator 50/1?
« on: March 15, 2016, 10:33:26 AM »
Well said. Mix it however you want to, realize you may need to compensate with jetting changes. I personally mix it at 50:1 just like Amsoil reccomends and designed it to be used.

3
Carburetor, Intake, and Exhaust / Amsoil Dominator 50/1?
« on: March 14, 2016, 08:22:17 AM »
I've ran it for the last 15 yrs in mine. It's fine at 50:1

4
Suspension and Chassis / Found my Roll a-arm setup issue...
« on: March 08, 2016, 10:02:00 AM »
Quote from: Tbone07;65272
Well that's good to know.

Does the 89' spindle have the tie-rod mount built in? The microfiche says it doesn't, but the pictures online say differently. Mine has that shitty extra bracket held on with 2 bolts.

Yes 89 is one piece. You have 86 if it bolts together.

5
Engine and Bottom End / Lean starting when cold??
« on: November 19, 2015, 03:30:59 PM »
I don't think that is uncommon. I try to prime my cylinder by kicking it through the stroke a few times slow with the ignition off first.

6
Lounge / Got burned again!
« on: November 02, 2015, 11:49:57 AM »
You should post this up on FB also if you are a group member to let anyone else aware of it. Be sure to tag him in it so you can get the satisfaction of that.

7
Lounge / Got burned again!
« on: November 02, 2015, 11:37:38 AM »
That Aintsokool of him.

8
Lounge / Stay far away from rodger schneider
« on: October 30, 2015, 04:08:33 PM »
:popcorn:

9
Lounge / cost to build a new trx from parts............link
« on: October 23, 2015, 09:28:15 AM »
They should start making plastic again and other parts because I know some guys who would be all over that! :onthego:

10
I need to get me a spare motor or two now damn!

11
Duner / When is next LS/waynoka trip?
« on: September 28, 2015, 02:16:26 PM »
Quote from: oldschoolr;59045
Even Don Wing showed up.
That's Hilarious!

12
Suspension and Chassis / Roll Swingarm and Pivot Bolt Bearing Issues
« on: September 15, 2015, 09:54:21 AM »
If it's frozen from rust, I have heard Kroil is some really good stuff. Never tried it myself.
http://www.3wheelerworld.com/showthread.php/175667-KROIL-OIL-Thank-You-Guys!

13
Pumashine 250R Products / Radiator clamp request
« on: September 09, 2015, 08:37:31 AM »
Quote from: bholzgen;58263
@Hawaiiysr http://www.trx250r.net/forum/photo-video/17352-i-finally-got-big-thanks-carlos-bdt.html

This is an excellent read.  So damn funny too.

Slot Car Site:
http://www.gofastest.com/ace/

That's hilarious! Wish I had time to read all 52 pages. Look at all the people from that thread that are now banned lol

14
Pumashine 250R Products / Radiator clamp request
« on: September 08, 2015, 03:10:29 PM »
Just spotted consulting with his lawyer
[ATTACH=CONFIG]9837[/ATTACH]

15
Pumashine 250R Products / Radiator clamp request
« on: September 08, 2015, 02:14:40 PM »
A real professional businessman who runs a real shop like Arlan or Eddie is far too busy to argue on forums EVERY day or any day for that matter. Simple as that, he's a joke. Never heard of him 10 yrs ago, crawled up out of the sewer like a rat and started claiming 30yrs experience, multiple championships, blah blah.
All I've ever seen was overpriced polished turds for sale on ebay, and buying all the NOS parts he can find then reselling it for 3X the price. "Helping the 250R Community"

Pages: [1] 2 3 ... 6