TRX250r.org

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nathan89

Pages: [1] 2 3
2
For Sale - Parts / For Sale: Stock 450r Front Shocks
« on: December 09, 2015, 05:20:30 PM »
bump...

3
For Sale - Parts / For Sale: Stock 450r Front Shocks
« on: November 26, 2015, 06:33:19 AM »
bump

5
For Sale - Parts / For Sale: Stock 450r Front Shocks
« on: November 25, 2015, 04:15:00 AM »
These are like new with very low hours. They were only used for a few months and then taken off the 450r. Came off a 2013 trx450r.

Fully adjustable, compression, rebound, and preload. These work great on the 250r especially if you have +2 a-arms.

Asking $235



6
Hey guys. I'm selling a few more of my spare parts. All parts are in great condition and ready to use. Ships from Saint Louis, Missouri. Reasonable offers may be considered. Prices do not include shipping.

86 transmission: $225

88/89 transmission: $300

Set of 3 shift forks: $110

Shift fork Shafts: $40

Shift Drum with Star: $50

Shift Shaft: $65

Counter Balancer: $75








7
For Sale - Parts / Billet Shift Forks for sale... Complete Set of 3
« on: November 10, 2015, 01:50:29 AM »
sold

8
For Sale - Parts / Billet Shift Forks for sale... Complete Set of 3
« on: November 08, 2015, 11:37:35 AM »
bump

9
For Sale - Parts / Billet Shift Forks for sale... Complete Set of 3
« on: November 06, 2015, 08:28:20 PM »
Hey guys I'm selling my extra set of Billet Shift Forks for any year 250r. These are top quality and a big upgrade over stock forks. These Billet forks also have an extra pad in the center to help evenly spread out pressure from the gears.

I only have one set that I am willing to sell so once this set sells, there are no more.

Asking $275 shipped.

Thanks, Nathan.


10
For Sale - Parts / Brand new esr cylinder kit for sale
« on: March 24, 2015, 07:49:51 PM »
................

11
Engine and Bottom End / New '01 CR Ignition
« on: November 09, 2014, 10:55:49 AM »
I have a brand new 01 CR ignition that I am going to install on my '86. I see the grommet where the wire comes out of the case cover is a bit larger on the CR then on the TRX. What do you guys do to get the CR grommet to fit correctly in the TRX case cut-out? Thanks guys.

12
Carburetor, Intake, and Exhaust / ESR ''New'' Reeds VS VF3
« on: September 19, 2014, 05:14:45 PM »
What do you guys prefer and why? I have a 310 ESR TRX9 port match race gas dome. Running a 38 airstriker carb. Is one of the reed blocks a better match to the trx9 port work?

Thanks

13
Lounge / New ESR goodies!
« on: September 15, 2014, 08:57:45 PM »
yeah it came with the jets, needle and o-ring. he also included an extra set of 3 o-rings in the bag with the exhaust flange. free throttle cover too :)

14
Lounge / New ESR goodies!
« on: September 15, 2014, 12:49:30 AM »
Finally got a 310 kit for my '86. Only one problem, Eddie forgot to put the piston in the box!! Oh well.. I'll call him Monday morning. At least he threw in a throttle cover and jet wrench!! Here's some cylinder porn for you guys. :ride:


















15
Lounge / I'm cheap.... but is this being a little too cheap??
« on: September 10, 2014, 05:02:02 PM »
im going to. i only have one air filter at the moment so i am waiting until i get a new one just in case it ruins the filter.

Pages: [1] 2 3