Author Topic: what did you do to your R today? (Read 107986 times)

Pricecheck · « **Reply #270 on:** July 17, 2014, 08:25:24 AM »

It wasn't today I did work but a couple of days ago I decided to tinker with the hybrid. Yfz motor sits 3/8" lower than frame so I have to box out the frame for protection. Mocked up an engine cradle so I can fab some motor mounts. Also cleaned up all of the unused mounts. Then I trimmed up the stock cdi mount and fabbed it to accept the yfz cdi and rectifier thing.

Not complete but I extended the mount to fit the rectifier and thinned the top plate to allow the cdi to attach. FYI.... I'm calling the black box thing the cdi. Maybe it's a distribution box.

Sent from my iPhone using Tapatalk

Pricecheck · « **Reply #271 on:** July 17, 2014, 08:26:49 AM »

The cdi slides on the tab. The rectifier mounts to the base once I weld some studs on it. It does clear the steering stem.

Sent from my iPhone using Tapatalk

Bigred · « **Reply #272 on:** July 17, 2014, 10:02:43 AM »

Put it on the trailer ready to go to pinelake

aberegg05 · « **Reply #273 on:** July 17, 2014, 10:51:09 AM »

Installed a pwr radiator yesterday. Hopefully thatll keep the heat down

hickwheeler · « **Reply #274 on:** July 17, 2014, 11:27:49 PM »

Just finished up mounting the trx5b cm and led intake I got from Mando.

broken1 · « **Reply #275 on:** July 18, 2014, 12:21:05 AM »

Heard my R run today for the first time in 2 years. Third gear went out in my engine, I picked up a spare engine last winter off craigslist & put my top end on it. Went from a long rod to a short rod.

mgleason05 · « **Reply #276 on:** July 20, 2014, 09:41:24 AM »

Replaced the handlebars, new hand guards, new rear tires, and new chain and sprockets.

zcarlson12 · « **Reply #277 on:** July 20, 2014, 03:19:24 PM »

New chain and sprockets installed. Mounting new LRD pipe this week.

ytman · « **Reply #278 on:** July 21, 2014, 06:45:31 AM »

Pictures...pictures.....pictures

zcarlson12 · « **Reply #279 on:** July 21, 2014, 07:32:32 PM »

As requested:

Trusty2stroke · « **Reply #280 on:** July 22, 2014, 12:23:31 PM »

This was over the last few days. Installed new crank seal, clutch plates, had counter balancer rebuilt, and installed new graphics.

ytman · « **Reply #281 on:** July 22, 2014, 05:31:56 PM »

Quote from: zcarlson12;39602

As requested:

MMMMMMMMMmmmmmmmm thank you

supernutt · « **Reply #282 on:** July 27, 2014, 09:02:48 PM »

Installed my "new to me" afco radiator in my trail machine. Seems to work pretty darn good. I can really feel the heat coming off it. Thanks kt23!!!

jamieg45 · « **Reply #283 on:** July 29, 2014, 02:11:45 AM »

OK Saturday, I pulled the axle and anti fade nut off of the Walsh. So burns363r kyle could use it to race on sunday.
Sunday I pulled the stem out of the lsr at my parents house so I can ship it. Monday after work I put the rear of the Walsh back together and put the mx tires on her so I can race on friday. Piston is in as well so top end will be finished up tomorrow after work.

08IRS · « **Reply #284 on:** July 29, 2014, 10:57:06 AM »

Just finished installing the CT pipe and silencer. I hope to install the radiator shrouds and front plastics today.