Author Topic: For Sale - PC2000 motor, Roll pegs + more (Read 5506 times)

Tbone07 · « **on:** June 09, 2014, 01:47:31 PM »

Duncan PC2000 275 motor - less than 5 hours on completely rebuilt engine top to bottom. Compression set at 185#, runs very, very strong.
New nikasil, crank, top-end, all bearings, seals, and bushings replaced. PC'd black side covers. Only typical case damage. Don't want to sell but I need a house
$1,200 shipped

88-89 Roll Pegs - 100% mint 10/10 condition
$225 shipped

LSR +2 ST A-Arms - Very good condition, no dents or dings, chrome is flaking a bit on upper right but not major. I ran these with 400EX spindles
$250 shipped

more to add later....

Kevhes11 · « **Reply #1 on:** June 09, 2014, 02:21:06 PM »

What's the bore and stroke on the motor

pinned250r · « **Reply #2 on:** June 09, 2014, 02:24:32 PM »

Daaaaaang

TRXforever · « **Reply #3 on:** June 09, 2014, 03:08:53 PM »

Double Daaaaaang!

SARON81 · « **Reply #4 on:** June 09, 2014, 03:21:15 PM »

Interested in selling the top end only?

Tbone07 · « **Reply #5 on:** June 09, 2014, 03:41:02 PM »

Pegs and a-arms sold pending payment.

Not interested in separating motor.

Thanks

Kevhes11 · « **Reply #6 on:** June 09, 2014, 05:17:59 PM »

Bore and stroke...

Vroomy · « **Reply #7 on:** June 09, 2014, 06:25:29 PM »

What size is the motor?

Sent from my iPhone using Tapatalk

Tbone07 · « **Reply #8 on:** June 09, 2014, 09:09:53 PM »

Quote from: Vroomy;36145

What size is the motor?

Sent from my iPhone using Tapatalk

Whoops.....updated....275

trx250scar · « **Reply #9 on:** June 09, 2014, 09:10:11 PM »

X3 What size engine bore and stroke. Also interested

Tbone07 · « **Reply #10 on:** June 09, 2014, 09:11:13 PM »

Quote from: Kevhes11;36138

Bore and stroke...

69.5mm bore x 72mm stroke

supernutt · « **Reply #11 on:** June 09, 2014, 10:09:53 PM »

What type of porting does the engine have? I thought they had a eliminator and a high rev and something else......but maybe that doesnt apply to the aftermarket cylinders..

mandom250r · « **Reply #12 on:** June 09, 2014, 10:16:38 PM »

Quote from: supernutt;36175

What type of porting does the engine have? I thought they had a eliminator and a high rev and something else......but maybe that doesnt apply to the aftermarket cylinders..

yea eliminator, national and hyperdyne. the hyperdyne is one of the first set-ups duncan did. it should be etched on the side of the cylinder. im thinking its a hyperdyne because this is an early model cylinder (check out the low rear base stud). there should be a number under the reeds part of the cylinder and if you give that to duncan they tell you every detail about that cylinder.

Tbone07 · « **Reply #13 on:** June 10, 2014, 09:46:30 AM »

Quote from: supernutt;36175

What type of porting does the engine have? I thought they had a eliminator and a high rev and something else......but maybe that doesnt apply to the aftermarket cylinders..

Engraved under the intake is "midrange"

Rockingkfarms · « **Reply #14 on:** June 10, 2014, 11:06:40 AM »

Sent you a text last night tbone