Author Topic: Everyone's profession (Read 63486 times)

StrokedAZ · « **Reply #45 on:** February 12, 2015, 07:17:13 PM »

I am a med tech in the lab of a hospital. I don't get to cut ANYTHING down!! This is total bulls**t! :eek:

Sent from my EVO using Tapatalk

rough250r · « **Reply #46 on:** February 12, 2015, 08:10:13 PM »

Quote from: Skeans1;50109

Wow that's some beautiful work

Thanks skeans Been banging nails for about ten years now... Tbone, that bowl is actualy from a piece of ambrosia maple. If I remember right it came from a crotch in a tree so that would explain all the "firey" patterns on the grain

Skeans1 · « **Reply #47 on:** February 12, 2015, 08:30:07 PM »

Quote from: Daniel370r;50150

^^^nope?

It's what we call a block face to make the top and butt hit at the same time as well as having little to no pull out of the log.

Sent from my iPhone using Tapatalk

Daniel370r · « **Reply #48 on:** February 12, 2015, 08:36:43 PM »

Interesting I don't know much about cutting wood for timber. I've cut some timber select cut for ppl I used a humbolt notch a small open face. All the cuts I use are to keep control 90% of the cutting I do is around powerlines water ways houses etc.

Skeans1 · « **Reply #49 on:** February 12, 2015, 09:03:58 PM »

I do lots of humboldt faces in different degrees of angle with a snipe off the stump or the butt if I want it to slide off the stump and not leave or to jump off the stump aways. The blocks are used a lot in bigger stuff just because of the control you or if the wood is too large for the bar so you can crawl in and cut.

Sent from my iPhone using Tapatalk

X~Stream Composites · « **Reply #50 on:** February 12, 2015, 11:56:33 PM »

Quote from: Skeans1;50119

Are you doing any 250r parts?

No, other than tie rods, as those are kind of universal. The atv retail world just isn't a place for me take make any money other than one off stuff like I did for Higgy.

X~Stream Composites · « **Reply #51 on:** February 13, 2015, 12:00:15 AM »

Quote from: beobe99;50153

Very nice, after seeing your work on other quads I think it's mandatory you make some stuff for the R! :chuncky:

Thanx!
I still have my 87 250R that has an LRD motor and I morphed a JP Owtlaw 250R into a CR250F that I custom built with Dave Moore for my then 14 year old son to race. He is now on a KTM 450SX... so the JP is now mine, and since it has 13" of rear wheel travel... it is nice on these old bones!

hub97119 · « **Reply #52 on:** February 13, 2015, 12:09:28 AM »

Urban logger here...used to work in the woods way back ( 70's ) started high climbing early 80's till today. That's a 3ft. bar on there and there has been too many times when Iv'e had to haul that bastard 60ft. into a tree.

hub97119 · « **Reply #53 on:** February 13, 2015, 12:27:03 AM »

but this is my real pride...coaching my youngest. Hope to move her up to a blaster this year

Skeans1 · « **Reply #54 on:** February 13, 2015, 01:41:52 AM »

Quote from: hub97119;50164

Urban logger here...used to work in the woods way back ( 70's ) started high climbing early 80's till today. That's a 3ft. bar on there and there has been too many times when Iv'e had to haul that bastard 60ft. into a tree.

Looks good.

Sent from my iPhone using Tapatalk

Skeans1 · « **Reply #55 on:** February 13, 2015, 01:43:17 AM »

Quote from: hub97119;50165

but this is my real pride...coaching my youngest. Hope to move her up to a blaster this year

Congrats I'm not too young but don't have any of my own yet enjoy it well you can.

Sent from my iPhone using Tapatalk

Skeans1 · « **Reply #56 on:** February 13, 2015, 01:44:22 AM »

Quote from: X~Stream Composites;50162

No, other than tie rods, as those are kind of universal. The atv retail world just isn't a place for me take make any money other than one off stuff like I did for Higgy.

If you need anything off a 250r or lt500 I'm just across the river.

Sent from my iPhone using Tapatalk

JesseA420 · « **Reply #57 on:** February 13, 2015, 08:01:44 AM »

machinist in a tool and die repair department of manufacturing facility. mostly been working on redesigning and replacing 20-30 yr old progressive die sets that were made with cutting torches and hand drills LOL

Rupp250 · « **Reply #58 on:** February 13, 2015, 10:36:48 AM »

I work for our local gas&electric utility managing guys out in the field on the gas side. Boring as heck but it is worth it every 2 weeks.

aberegg05 · « **Reply #59 on:** February 13, 2015, 10:58:20 AM »

I'm a coal miner.