Author Topic: My Junk (Read 34177 times)

atv fan 28 · « **Reply #45 on:** July 18, 2013, 12:00:44 AM »

Quote from: traxman;4410

Dang, Wayne I wish my chit could look that nice..

it would if you used this stuff.....

traxman · « **Reply #46 on:** July 18, 2013, 12:27:05 AM »

I tried that stuff once and ended up puking all over the place. I couldn't stand the smell.. I guess I'll focus on performance rather than polishing the turd!!!

atv fan 28 · « **Reply #47 on:** July 18, 2013, 12:34:53 AM »

ouch that hurt!!! so you are saying polished motors are slower??

Pumashine · « **Reply #48 on:** July 18, 2013, 01:15:22 AM »

Quote from: traxman;4410

Dang, Wayne I wish my chit could look that nice..

Is that the kettle calling the pot shiny? LMAO

genoapb · « **Reply #49 on:** July 19, 2013, 04:20:22 AM »

I think this is my favorite 250r!

Morse250r · « **Reply #50 on:** July 19, 2013, 05:41:16 AM »

Get some heat in it yet Wayne?

??

atv fan 28 · « **Reply #51 on:** July 19, 2013, 09:12:35 PM »

Quote from: Morse250r;4584

Get some heat in it yet Wayne???

it will tomorrow if everything goes right!

rsss396 · « **Reply #52 on:** July 19, 2013, 10:06:58 PM »

when you crank that motor with the electric starter make sure the you have the cdi unplugged or kill switch on so it does not fire right away crank it a little like 10 revolutions or so to get some fuel in the bottom end or some times it will start lean and rev to the moon until fuel gets in the bottom end

atv fan 28 · « **Reply #53 on:** July 19, 2013, 10:20:36 PM »

No electric starter with this motor...

traxman · « **Reply #54 on:** July 20, 2013, 10:53:37 AM »

Quote from: rsss396;4706

when you crank that motor with the electric starter make sure the you have the cdi unplugged or kill switch on so it does not fire right away crank it a little like 10 revolutions or so to get some fuel in the bottom end or some times it will start lean and rev to the moon until fuel gets in the bottom end

Just kick it 5-10 times with the ignition off to help prevent it. Also if it does run away kill the ignition, put the rear brake on, drop it in gear and dump the clutch to stop it. I usually put about a 1/2" to 3/4" of fuel in the bottom of the bowl to help start the bike and as soon as it fires turn on the alky. It acts like a choke for the colder weather and starts easier for me.

atv fan 28 · « **Reply #55 on:** July 20, 2013, 10:06:39 PM »

kicked it over a few times slowly then gave it one good kick and she came alive!!!

atv fan 28 · « **Reply #56 on:** July 21, 2013, 11:00:30 PM »

View My Video

363 stroker · « **Reply #57 on:** July 22, 2013, 12:21:24 AM »

Angry !!!!!!!!!!!

atv fan 28 · « **Reply #58 on:** July 23, 2013, 12:07:06 AM »

Quote from: 363 stroker;5005

Angry !!!!!!!!!!!

dont be mad!!!

Duner · « **Reply #59 on:** July 23, 2013, 06:04:12 AM »

Quote from: atv fan 28;4420

ouch that hurt!!! so you are saying polished motors are slower??

This was actually a debate once....as was polishing cylinders/pipe rather then leaving it in its rough state...

Vid is sweet WW